Intel 4 519K HH80547PE0831MN Ficha De Dados
Códigos do produto
HH80547PE0831MN
22
Datasheet
Electrical Specifications
Table 9. Voltage and Current Specifications
Symbol
Parameter
Min
Typ
Max
Unit
Notes
1
VID range
VID
1.250
1.400
V
2
V
CC
V
CC
Loadline A processors
3.20E GHz (PRB = 1)
3.40E GHz (PRB = 1)
VID – I
CC
(max) * 1.45 m
Ω
V
V
CC
V
CC
Loadline B processors
2.80A/E GHz (PRB = 0)
3E GHz (PRB = 0)
3.20E GHz (PRB = 0)
3.40E GHz (PRB = 0)
See
and
VID – I
CC
(max) * 1.45 m
Ω
V
3,4,5
I
CC
I
CC
for processor with multiple VID:
2.80A/E GHz (PRB = 0)
3E GHz (PRB = 0)
3.20E GHz (PRB = 0)
3.40E GHz (PRB = 0)
3.20E GHz (PRB = 1)
3.40E GHz (PRB = 1)
78
78
78
78
91
91
A
6
I
SGNT
I
SLP
I
CC
Stop-Grant:
2.80A/E GHz (PRB = 0)
3E GHz (PRB = 0)
3.20E GHz (PRB = 0)
3.40E GHz (PRB = 0)
3.20E GHz (PRB = 1)
3.40E GHz (PRB = 1)
40
40
40
40
50
50
A
7,8,10
I
TCC
I
CC
TCC active
I
CC
A
9
I
CC
_
VCCA
I
CC
for PLL pins
60
mA
10
I
CC
_
VCCIOPLL
I
CC
for I/O PLL pin
60
mA
I
CC
_
GTLREF
I
CC
for GTLREF pins (all pins)
200
µA
I
CC
_
VCCVID
/
VCCVIDLB
I
CC
for V
CCVID
/V
CCVIDLB
150
mA
NOTES:
1.
Unless otherwise noted, all specifications in this table are based on estimates and simulations or empirical data.
2.
Individual processor VID values may be calibrated during manufacturing such that two devices at the same speed may have
different VID settings.
different VID settings.
3.
These voltages are targets only. A variable voltage source should exist on systems in the event that a different voltage is re-
quired. See
quired. See
4.
The voltage specification requirements are measured across VCC_SENSE and VSS_SENSE pins at the socket with a
100 MHz bandwidth oscilloscope, 1.5 pF maximum probe capacitance, and 1 M
100 MHz bandwidth oscilloscope, 1.5 pF maximum probe capacitance, and 1 M
Ω minimum impedance. The maximum length
of ground wire on the probe should be less than 5 mm. Ensure external noise from the system is not coupled into the oscillo-
scope probe.
scope probe.
5.
/
/
for the minimum, typical, and maximum V
CC
allowed for a given current. The
processor should not be subjected to any V
CC
and I
CC
combination wherein V
CC
exceeds V
CC
_
MAX
for a given current. Moreover,
V
CC
should never exceed the VID voltage. Failure to adhere to this specification can shorten the processor lifetime.
6.
I
CC
_
MAX
is specified at V
CC
_
MAX
7.
The current specified is also for the AutoHALT State.
8.
I
CC
Stop-Grant and I
CC
Sleep are specified at V
CC_MAX
.
9.
The maximum instantaneous current the processor will draw while the thermal control circuit is active as indicated by the as-
sertion of PROCHOT# is the same as the maximum I
sertion of PROCHOT# is the same as the maximum I
CC
for the processor.