Honeywell ADEMCO 6150RF Guia Da Instalação
- 6 -
Step Action
Display
6.
(Cont’d)
Wireless Key Function Chart
Function
Entry
Disarming
1
Arming Away
2
Arming Stay
3
Arming Maximum (Away Instant)
4
Arming Instant
7
Panic Alarm
Produces type of alarm [* & #]
programmed in control panel.
# + 99
Manually Start a Relay Action
# + 7 (VISTA-10SE, VIA-30PSE)
# + 7 + n (VISTA-10P, VISTA-15P,
VISTA-20P, VISTA-20SE(HW))
Manually Stop a Relay Action
# + 8 (VISTA-10SE, VIA-30PSE)
# + 8 + n (VISTA-10P, VISTA-15P,
VISTA-20P, VISTA-20SE(HW)
Activate Relay as Programmed in
Control
# + 71 (VISTA-40, VISTA-50P,
VISTA-128B)
Activate Relay as Programmed in
Control
# + 72 (VISTA-40, VISTA-50P,
VISTA-128B)
Activate Access Control Relay for
Partition
0 (VISTA-40, VISTA-50P, VISTA-
128B)
n = Device Number programmed in panel to be controlled
Press the [
✻] key.
Default Loop Functions
5 8 0 4
Loop 3
Arm AWAY
Arm AWAY
Loop 1
Close on-board relay
for 2 seconds
Close on-board relay
for 2 seconds
Loop 2
Disarm
Disarm
Loop 4
Arm STAY
5 8 0 4 B D / 5 8 0 4 B DV
Loop 3
Arm AWAY
Loop 1
Close on-board relay
for 2 seconds
Close on-board relay
for 2 seconds
Loop 2
Disarm
Disarm
SET
HOUSE
CODE
•
•
••
•
•
•
•
•
•
•
•
•
• •
•
•••
Loop 4
Arm STAY
Arm STAY
NOTE: If the loop is defaulted with a function (e.g.,
Arm, Disarm) and also is assigned to activate
the on-board relay, the system performs
BOTH functions.
7.
Repeat step 6 for the rest of the loops of the wireless key.
8.
To program a button on the wireless key to control the on-board
relay, enter [5] (On-Board Relay Assignment).
relay, enter [5] (On-Board Relay Assignment).
Flashes "o-."
9.
Enter the loop number of the wireless key (1-4). Enter the relay
action (0 = no action; 1 = relay off; 2 = relay on; 3 = relay toggles on
and off; 4 = relay closes for 2 seconds).
action (0 = no action; 1 = relay off; 2 = relay on; 3 = relay toggles on
and off; 4 = relay closes for 2 seconds).
Note: The relay action must be "0" for UL installations.
Press the [
✻] key.
Flashing “o” and the loop number.
Once the action is entered, displays “o” and
alternately flashes the loop number and the relay
action.
Once the action is entered, displays “o” and
alternately flashes the loop number and the relay
action.
10.
Repeat step 9 for the rest of the loops.
11.
When all loops have been programmed for the wireless key, press the
[
[
✻] key.
Flashes “d” followed by the device number.
12.
The 6150RF automatically displays the next available device number
(one that does not have a serial number).
(one that does not have a serial number).
If you want to program additional wireless keys, repeat steps 3
through 10. Otherwise, press the [#] key. This takes you back to the
main display, which alternately flashes “oo” and “- -.”
through 10. Otherwise, press the [#] key. This takes you back to the
main display, which alternately flashes “oo” and “- -.”
13.
Enter [0] (High Security Mode). To put the system into High-Security
mode, enter [1]. Enter [0] to disable.
mode, enter [1]. Enter [0] to disable.
Flashes “En” and “0” alternately OR “En” and
“1” if the keypad is in high-security mode
14.
Press [
✻] to exit the 6150RF Program mode.
Note: Upon exiting the Program mode, the 6150RF alternately flashes "Ad," the 2-digit keypad address, and the 2-digit receiver
address. If either of these is incorrect, repeat steps 1 through 3 in the Programming for an Installation Without Local Wireless
Keys section.
Keys section.
Deleting, Replacing, or Editing Wireless Keys
Use the following procedure to delete, replace, or change any of the programming for a wireless key.
Use the following procedure to delete, replace, or change any of the programming for a wireless key.
Step
Action
Display
1.
Enter the Program mode by pressing the [1] and [3] keys
simultaneously for a few seconds within 30 seconds after applying
power.
simultaneously for a few seconds within 30 seconds after applying
power.
Alternately flashes "oo" and two dashes.
2.
Enter [5] (Wireless Key Editing). Enter the device number for the
wireless key you want to edit. This must be a device that has its
serial number programmed in the 6150RF already.
To delete the serial number, press [
wireless key you want to edit. This must be a device that has its
serial number programmed in the 6150RF already.
To delete the serial number, press [
✻], then press [9], and press [✻]
again.
To exit without deleting the serial number, press the [#] key.
Press the [
To exit without deleting the serial number, press the [#] key.
Press the [
✻] key to continue.
Flashes the device number and a hyphen.
Once the device number is entered, alternately
Once the device number is entered, alternately
flashes "d" with the device number; and the serial
number.
number.