Enviro EG 33 Manual Do Utilizador
TABLE OF CONTENTS
Safety Precautions
2
Code Approvals
3
Assembly Instruction
3
Deciding where to locate your stove
4
Mobile Home Information
4
Installation
5-6
Mantle and Vent restrictions
7
Flue Collar Installation and Vent terminal clearances
8
Planning your installation
9-13
Installation of Log Sets and Embers
14
Operating Instructions
15
Maintenance and Technical
16
Trouble Shooting
17
Gas Line Connection
18
Electrical
19
Fuel Conversion
20
Warranty
21
Installation Data Sheet
22
CODE APPROVALS
• This Direct Vent appliance draws all of its combustion air from outside of the dwelling through specially
designed vent pipe.
• These appliances have been tested by INTERTEK (ITS)(WH) services and found to comply with the
established standards for a DIRECT VENT GAS FIREPLACE in CANADA and the USA as follows:
LISTED GAS FIRED GRAVITY DIRECT VENT WALL FURNACE (EG 33 DV. NAT. & LPG. )
TESTED TO: ANSI Z21.44-1995 (GAS FIRED GRAVITY DIRECT VENT WALL FURNACE), CAN1-2.19-M81 (VENTED
GRAVITY DIRECT VENT WALL FURNACE), ANSI Z21.88-1998/CSA 2.33-M98 (VENTED GAS FIREPLACE HEATER)
UL
307B-1995 GAS BURNING HEATING APPLIANCES FOR MANUFACTURED HOMES. CGA 2.17-M91 GAS FIRED
APPLIANCES FOR USE AT HIGH ALTITUDE.
APPLIANCES FOR USE AT HIGH ALTITUDE.
SPECIFICATIONS:
ENVIROGAS EG 33 DIRECT VENT UNITS;
• Have all been certified for use with either natural or propane gases. (see control panel and rating label.)
• Are not for use with solid fuels.
• Must not be connected to a chimney flue serving a separate solid-fuel burning appliance.
• Are approved for bedroom or bedsitting room.
• Have all been certified for use with either natural or propane gases. (see control panel and rating label.)
• Are not for use with solid fuels.
• Must not be connected to a chimney flue serving a separate solid-fuel burning appliance.
• Are approved for bedroom or bedsitting room.
(IN CANADA: must be installed with a listed wall thermostat)
(IN USA: see current ANSI Z223.1 for installation instructions.)
(IN USA: see current ANSI Z223.1 for installation instructions.)
• Must be installed in accordance with local codes if any. If none exist use current installation code CAN/CGA
b149 in Canada or ANSI Z223.1 / NFPA 54 in the USA.
• Must be properly connected to an approved venting system.
• Manufactured (mobile) home installation must be in accordance with the Manufactured Home Construction
• Manufactured (mobile) home installation must be in accordance with the Manufactured Home Construction
and Safety Standard, UL 307B, Title 24 CFR, Part 3280 and/or The Standard for Manufactured Home
Installations, ANSI A225.1/NFPA 501A. The unit must be bolted to the floor of the mobile home and must be
electrically grounded to the steel chassis.
Installations, ANSI A225.1/NFPA 501A. The unit must be bolted to the floor of the mobile home and must be
electrically grounded to the steel chassis.
• Are approved for installation on combustible materials.
PREPARATION FOR INSTALLATION
• Remove the packaging from the appliance, and check to make sure there is no damage. If damage is found,
please report it to both the carrier and your dealer as soon as possible.
• Before beginning, carefully check the glass door and the log set
ASSEMBLY:
• The stove is now ready to be connected to the gas supply.
• Install the embers (single layer thick, including on top of the burner). Install the logset into the firebox.
• Install the embers (single layer thick, including on top of the burner). Install the logset into the firebox.
3