Apollo ESP6000 Manual Do Utilizador
User’s Manual
ECM-3612 User’s Manual
71
3.5.4.6 IDE HDD Block Mode
Block mode is also called block transfer, multiple commands, or multiple sector read/write.
If your IDE hard drive supports block mode (most new drives do), select Enabled for
automatic detection of the optimal number of block read/writes per sector the drive can
support.
The choices: Enabled, Disabled.
Block mode is also called block transfer, multiple commands, or multiple sector read/write.
If your IDE hard drive supports block mode (most new drives do), select Enabled for
automatic detection of the optimal number of block read/writes per sector the drive can
support.
The choices: Enabled, Disabled.
3.5.4.7 Onboard Lan Boot ROM
This item allows to boot over the network when system POST and shorten the booting time
by set disabled.
The choices: Enabled, Disabled.
This item allows to boot over the network when system POST and shorten the booting time
by set disabled.
The choices: Enabled, Disabled.
3.5.4.8 Onboard FDD Controller
This item allows to enable/disable the onboard floppy drive controller. If an add-on FDD
controller or any floppy drive at all, set to disabled to save an IRQ.
The choices: Enabled, Disabled.
This item allows to enable/disable the onboard floppy drive controller. If an add-on FDD
controller or any floppy drive at all, set to disabled to save an IRQ.
The choices: Enabled, Disabled.
3.5.4.9 Onboard Serial Port 1 / 2
Select an address and corresponding interrupt for the first and second serial ports.
The choices: Disabled, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3.
Select an address and corresponding interrupt for the first and second serial ports.
The choices: Disabled, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3.
3.5.4.10 UART 2 Mode
Select UART 2 mode as standard serial port or IR port.
The choices: Standard, HPSIR, ASKIR.
Select UART 2 mode as standard serial port or IR port.
The choices: Standard, HPSIR, ASKIR.
3.5.4.11 IR Function Duplex
Select the value required by the IR device connected to the IR port. Full-duplex mode
permits simultaneous two-direction transmission. Half-duplex mode permits transmission in
one direction only at a time.
Select the value required by the IR device connected to the IR port. Full-duplex mode
permits simultaneous two-direction transmission. Half-duplex mode permits transmission in
one direction only at a time.
The choices: Full, Half.
3.5.4.12 TX,RX inverting enable
This item allows you to determine the active of RxD, TxD level.
This item allows you to determine the active of RxD, TxD level.
The choices: No,No, No,Yes, Yes,No, Yes,Yes.
3.5.4.13 Onboard Parallel Port
Select a logical LPT port name and matching address for the physical parallel (printer) port.
The choicse: Floppy, 378H/IRQ7, 278H/IRQ5, 3BCH/IRQ7, Disabled
Select a logical LPT port name and matching address for the physical parallel (printer) port.
The choicse: Floppy, 378H/IRQ7, 278H/IRQ5, 3BCH/IRQ7, Disabled
3.5.4.14 Onboard Parallel Mode
Select an operating mode for the parallel port. Select Compatible or Extended unless you
are certain both your hardware and software support EPP or ECP mode.
The choices: EPP, ECP, ECP/EPP, Normal.
Select an operating mode for the parallel port. Select Compatible or Extended unless you
are certain both your hardware and software support EPP or ECP mode.
The choices: EPP, ECP, ECP/EPP, Normal.