Behringer FCB1010 Manual Do Proprietário
8
MIDI FOOT CONTROLLER FCB1010 User Manual
Switch
MIDI Function
Action
1
PRG CHG 1
Program change command #1
2
PRG CHG 2
Program change command #2
3
PRG CHG 3
Program change command #3
4
PRG CHG 4
Program change command #4
5
PRG CHG 5
Program change command #5
6
CNT 1
Controller 1
7
CNT 2
Controller 2
8
EXP A
Expression Pedal A
9
EXP B
Expression Pedal B
10/0
NOTE
Transmits a MIDI note
Tab. 2.3: Footswitch assignment in PRESET programming mode
◊
MIDI channel adjustment for the respective MIDI functions is not done
during preset programming; it is done in GLOBAL CONFIGURATION on
MIDI FUNCTION page (see ch. 2.2.2).
during preset programming; it is done in GLOBAL CONFIGURATION on
MIDI FUNCTION page (see ch. 2.2.2).
•
Confirm your selection with UP/ENTER, in order to start programming the
selected MIDI function, or cancel with DOWN/ESCAPE. Use footswitches
1 through 10/0 or EXPRESSION PEDAL A to enter the parameter values of
your choice.
•
If you have selected PROGRAM CHANGE as the MIDI function to be edited,
you can now enter a program change number from 1 through 128 and
confirm your selection with UP/ENTER.
•
If you have selected CNT1 or CNT2, you can now enter the number of the
controller to be sent (0 through 127) when you press the corresponding
footswitch. After confirming your selection with UP/ENTER you can select a
controller value (0 through 127). Confirm your selection with UP/ENTER.
•
If you have selected EXP A or EXP B, you can now enter the controller
number the EXPRESSION PEDAL of your choice is aimed to send values for.
Confirm your selection with UP/ENTER and enter the lower value (pedal up).
Confirm with UP/ENTER.
•
Afterwards, enter the upper value (pedal pressed down completely)
and confirm once again with UP/ENTER.
◊
Please keep in mind that the first controller value always has to be
lower than the second controller value!
lower than the second controller value!
◊
You can quit the programming mode at any time by means of a long
press on DOWN. Any confirmed entries will be stored with the currently
selected PRESET.
press on DOWN. Any confirmed entries will be stored with the currently
selected PRESET.
◊
How to program the NOTE function is explained in chapter 2.4.6.
2.4 Detailed PRESET programming
2.4.1 Preset copy function
The preset copy function copies an already programmed preset to a new preset of
The preset copy function copies an already programmed preset to a new preset of
your choice. This saves you time, since you do not have to repeat all adjustments
for each newly programmed preset.
•
Activate CONFIG in the GLOBAL CONFIGURATION (see chapter 2.2).
•
Now, press footswitch 5 to activate the copy function. The VALUE 1 LED lights
up. The number in the display and the footswitch LED start flashing.
•
Enter the number of the preset you wish to copy and confirm your selection
with UP/ENTER. The VALUE 2 LED lights up. The number in the display and
the footswitch LED start flashing.
◊
Presets 1 - 10 are stored in bank 0, presets 11 - 20 in bank 1, and so on.
•
Enter the target preset and confirm your selection with UP/ENTER, or cancel
with DOWN/ESCAPE.
•
If you want to copy further presets, please press footswitch 5 again.
Press and hold DOWN/ESCAPE to quit the GLOBAL CONFIGURATION.
2.4.2 Programming switches
•
Select the PRESET you wish to edit.
•
Press DOWN for more than 2.5 sec to enter PRESET programming mode.
The green SWITCH 1/SWITCH 2 LED in the display starts flashing.
•
Enable/disable the SWITCHES using footswitches 1 and/or 2 and confirm your
selection with UP/ENTER. The corresponding footswitch and SWITCH LEDs
light up.
•
Exit PRESET programming mode through keeping the DOWN/ESCAPE key
for a few seconds, or press the UP/ENTER key in order to get to the next
page, where you can edit various MIDI functions for the preset selected at
the beginning.
2.4.3 Programming program changes
•
Select the PRESET you wish to edit.
•
Keep the DOWN/ESCAPE key pressed longer than 2.5 sec. to get to the
programming mode. The green SWITCH 1/SWITCH 2 LED in the display
starts flashing.
•
Use the UP/ENTER key to get to the next page. The SELECT LED in the display
is lit.
◊
To program a MIDI function, you have to first activate it. Individual
MIDI functions are activated by keeping the corresponding keys
pressed for a few seconds. Active MIDI functions are indicated by a
permanently lit footswitch LED.
MIDI functions are activated by keeping the corresponding keys
pressed for a few seconds. Active MIDI functions are indicated by a
permanently lit footswitch LED.
•
Select the PROGRAM CHANGE you wish to program for the selected
PRESET by briefly pressing the respective footswitch (footswitches 1 to 5).
The footswitch LED blinks.
•
Confirm your selection by pressing UP/ENTER. The NUMBER LED in the display
lights up.
•
Enter the program change command (1 bis 128) via the footswitch or
expression pedal A.
•
Confirm your selection by pressing UP/ENTER or cancel by pressing
DOWN/ESCAPE. The SELECT LED in the display lights up.
•
Select an additional MIDI function you wish to edit or exit the PRESET
programming mode by keeping the DOWN/ESCAPE key for a few seconds.
2.4.4 Programming CONTROL CHANGES
•
Select the PRESET you wish to edit.
•
Keep DOWN pressed for more than 2.5 sec to enter PRESET programming
mode. The green SWITCH 1/SWITCH 2 LED in the display starts flashing.
•
Use the UP/ENTER key to get to the next page. The SELECT LED in the display
lights up.