Laney Amplification Music Mixer Concept 10 Manual Do Utilizador
Concept
Concept Manual
14
The fader sets the output level of the Auxiliary to be sent to the
MASTERS .
MASTERS .
FADER
The Mon control is set for pre-fade operation for use a monitor
send.The signal passes to the feedback filter and monitor fader in
the master section before leaving by the jack socket marked Mon.
send.The signal passes to the feedback filter and monitor fader in
the master section before leaving by the jack socket marked Mon.
PFL
MON
BAL
Adjusts the stereo signal level to the left and right master
outputs,the signal being sent equally left and right when set central.
outputs,the signal being sent equally left and right when set central.
The pre fade listen switch when depressed directs the 'pre fader'
Auxiliary signal to the right hand 'bargraph' (VU) display and
headphones, allowing Auxiliary signal' to be set and cued. This is
non destructive so may be used at any time during the
performance without effecting the main.
Auxiliary signal to the right hand 'bargraph' (VU) display and
headphones, allowing Auxiliary signal' to be set and cued. This is
non destructive so may be used at any time during the
performance without effecting the main.
Controls the level of the Stereo Auxilliary/Tape input signal to the
monitor.
monitor.
Stereo Auxilliary / Tape Input Phono (RCA) sockets are
provided for the connection of tape/DAT machines. The
signal to monitor and master outputs can be
independently controlled via the controls labelled 'Tape to
monitor' and 'Tape to master'. PFL monitoring of the
tape to master signal is provided.
provided for the connection of tape/DAT machines. The
signal to monitor and master outputs can be
independently controlled via the controls labelled 'Tape to
monitor' and 'Tape to master'. PFL monitoring of the
tape to master signal is provided.
A Stereo Auxiliary Input for use as an FX return or as an additional
stereo input .
Stereo signals can be input either on a stereo jack or L + R on
mono jacks.If required the Auxilary can be used as a mono input
by inputting on the socket labelled Mono.
stereo input .
Stereo signals can be input either on a stereo jack or L + R on
mono jacks.If required the Auxilary can be used as a mono input
by inputting on the socket labelled Mono.
48V Phantom Power is provided for condenser microphones.
It is globaly switched to all mic XLR sockets via this recessed
switch.
It is globaly switched to all mic XLR sockets via this recessed
switch.
Phantom power must always be switched off when using
unbalanced sources connected to mic inputs otherwise the source
may be damaged
unbalanced sources connected to mic inputs otherwise the source
may be damaged
Condenser microphones should be connected to mic inputs before
the phantom power is switched on.
the phantom power is switched on.
Controls the level of the Stereo Auxilliary/Tape input signal to the
Masters
Masters
STEREO AUXILIARY/TAPE INPUT
AUXILIARY INPUTS
STEREO AUXILIARY
TO MONITOR
48V Phantom
TO MASTER
PFL
PFL
MON
MON
PFL
PFL
L R
L R
LEFT
LEFT
RIGHT
RIGHT
MONO
MONO
STEREO
STEREO
STEREO AUXILIARY
/TAPE INPUT
/TAPE INPUT
STEREO AUXILIARY
/TAPE INPUT
/TAPE INPUT
STEREO AUXILIARY
STEREO AUXILIARY
BAL
BAL
FADER
FADER
POWER
POWER
STEREO AUXILIARY
/TAPE INPUT
/TAPE INPUT
STEREO AUXILIARY
/TAPE INPUT
/TAPE INPUT
TO
MON
MON
TO
MON
MON
TO
MASTER
MASTER
TO
MASTER
MASTER
48V
PHANTOM
PHANTOM
48V
PHANTOM
PHANTOM
18
19
20
21
22
23
10
24
25
26
10
18)
19
+20)
+20)
21)
22)
23)
10)
25)
24)
26)