Dacor RSE30 Manual Do Utilizador

4. do not install a fuse in the

neutral or ground circuit. A

fuse in the neutral or ground

circuit may result in an

electrical shock hazard.

5. do not ground the appliance

to a gas supply pipe or hot

water pipe.

6. A grounded cold water pipe

must have metal continuity to

electrical ground and must not

be interrupted by insulating

materials. Any insulating

materials must be jumped

with a length of No. 4 copper

wire securely clamped to bare

metal at both ends.

Grounding Instructions (All Models)

This appliance must be electrically

grounded.

With the range positioned directly in front of

the cabinet cutout, feed the appliance conduit

to the electrical junction box. Then, depending

upon local codes, utilize one of the following

techniques to connect the appliance to the

electrical power supply:

A. Connecting to a Four-wire Electrical

System. (Recommended for All Models)

1. Separate the green and white appliance

wires.

2. Connect the white appliance wire to the

neutral (white) supply wire in the junction

box.

3. Connect the black appliance wire to the

black (L1) power supply wire in the junction

box.

4. Connect the red appliance wire to the red

(L2) power supply wire in the junction box.

5. Connect the green appliance wire to the

green house grounding wire in the junction

box.

Door Opened

Range Top

23 1/2"

(597mm)

26 9/16"

(675mm)

Rear of Control

Panel/Oven Door

Max. depth

to oven door

handle with

door closed

30"

(762mm)

45 1/4"

(1149mm)

Overall dimensions (Preference Models)

Isometric View

Door Opened

Range Top

23 1/2"

(597mm)

25 5/16"

(643mm)

Rear of Control

Panel/Oven Door

Max. depth

to oven door

handle with

door closed

30"

(762mm)

45 1/4"

(1149mm)

Overall dimensions (MRES Model)

Isometric View

Installing the Anti-Tip Bracket

wARNING:

This appliance require an anti-

tip device. Before installing the

range, you must locate and secure

the anti-tip bracket to the floor.

When the range is slid into position in the

cutout, the left rear leveling leg slides into this

bracket to prevent the unit from tipping forward.

The bracket location shown here will position the

rear edge of the range top frame flush to the rear

wall. From this position, the bracket allows for up

to 5/8” (16mm) of forward movement of the range.

1 1/2”

(38mm)

24”

(610mm)

1”

(25mm)

11 3/8”

(289mm)

2 3/16”

(556mm)

Front face

of cabinet

19 7/16”

(494mm)

Location of Anti-Tip Bracket

Top View

Removing the Oven door

wARNINGS:

1. do not attempt to disengage

the hinge catches with the

door removed from the oven.

The hinge springs could

release causing personal

injury.

2. do not lift or carry the oven

door by the door handle.

Open the door to its fully opened position.

Rotate the catch over the retaining arm on each

hinge. Lift the oven door to about a 30 degree

angle from the horizontal position. Pull the door

away from the oven while continuing to lift.

Removing the Oven door

Remove the kick Panel (All Models)

Remove the screw at each top corner of the

kick panel. Lift up slightly on the panel and pull

forward to remove

Electrical Connection

NOTE:

See the range data plate for

electrical specifications. See

page 1 for location.

wARNINGS:

1. All of these range models

must be connected to a

grounded, metallic, permanent

wiring system. Alternatively, a

grounding conductor should

be connected to the grounding

terminal or lead on the

appliance.

3. do not use an extension cord

with this appliance. Such use

may result in fire, electrical

shock, or other personal

injury.

Conduit from

appliance

Cable from

power supply

Wire nut

(4 places)

Junction

box

RED
RED

GREEN
GREEN

WHITE
WHITE

BLACK
BLACK

Connecting the appliance to a

four-wire power supply

(All Models)