BEA 10MATRIX Manual Do Utilizador

BACK VIEW

     Main

Connector

 (86CP11)

DIGITAL INDUCTIVE LOOP SENSORS

75.1046.04   EN  20080505 

 

 

            

 

 

Page 1 of 5



Shut off all power before attempting any wiring procedures.



Maintain a clean & safe environment when working in public areas.



Constantly be aware of pedestrian traffic around the door area.



Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.



ESD:  Circuit boards are vulnerable to damage by electrostatic discharge.  Before handling any board ensure you dissipate your body’s charge.



Always check placement of all wiring before powering up to insure that moving door parts will not catch any wires and cause damage to equipment.



Ensure compliance with all applicable safety standards (i.e. ANSI A156.10 / A156.19) upon completion of installation.



DO NOT attempt any internal repair of the sensor. All repairs and/or component replacements must be performed by BEA, Inc. Unauthorized disas-
sembly or repair:

1.  May jeopardize personal safety and may expose one to the risk of electrical shock.
2.  May adversely affect the safe and reliable performance of the product will result in a voided product warranty.

The MATRIX (10MATRIX) Digital Inductive Loop Detector is the ideal solution for parking barrier control, motorized gates and doors, vehicle 
access control and industrial control systems.  The MATRIX is a high performance single or dual-channel vehicle detector packaged in a 

compact housing.  The connection is made with a standard industrial 11-pin round connector.  The six versions listed below include single or 

dual-channel, and 3 possible power supplies:

10MATRIXS110   : Single loop detector with 110 to 120 V AC power supply.
10MATRIXS220   : Single loop detector with 220 to 240 V AC power supply.
10MATRIXS1224 : Single loop detector with 12 to 24 V AC/DC power supply.
10MATRIXD110   : Dual loop detector with 110 to 120 V AC power supply.
10MATRIXD220   : Dual loop detector with 220 to 240 V AC power supply.
10MATRIXD1224 : Dual loop detector with 12 to 24 V AC/DC power supply.

“The Peak Of Detection” 

Power LED

Dip Switches

Detection State LED

Presence Time

  Adjustment

Potentiometer

Sensitivity Adjustment

        Potentiometer

      (Dual Loop Only)

Detection State LED

   (Dual Loop Only)

Sensitivity Adjustment

        Potentiometer

TERMINOLOGY

SPECIFICATION

TERMINOLOGY

SPECIFICATION

TECHNOLOGY

Inductive Loop

POWER FREQUENCY

48 to 62 Hz

TUNING

Automatic

POWER CONSUMPTION

< 2.5 W

DETECTION MODE

Presence

TEMPERATURE RANGE

-22ºF to 158ºF (-30ºC to 70ºC)

PRESENCE TIME

1 min to infinity with 250 steps

DEGREE OF PROTECTION

IP40

PULSE TIME OUTPUT

100 ms or 500 ms

WEIGHT

7 oz. (<200g)

LED INDICATORS

Power:  Green
Loop Status 1:  Red
Loops Status 2:  Red

PROTECTIONS

Loop Insulation Transformer
Zener Diodes
Gas Discharge Clamping

FREQUENCY RANGE

20 kHz to 130 kHz

INDUCTANCE RANGE

20 H to 1000 H

FREQUENCY STEPS

Single Loop:  4
Double Loop:  2 (for each loop)

DIMENSIONS

3.0 in (H) x 1.5 in (W) x 3.0 in (D)

(76mm x 38mm x 76mm)

SENSITIVITY (ΔL / L)

0.005% to 0.5% with 250 steps

CONNECTION

86CP11 (Standard 11-Pin Round)

REACTION TIME

Single Loop:  25ms  
Double Loop: 50ms (ea. channel)

2 OUTPUT RELAYS (free po-
tential change-over contact)

Max Contact Voltage:  230 VAC

Max Contact Current:  5A (res.)

SETUP TIME AFTER CONFIGURATION

2 s max by channel

SETUP TIME AT POWER ON

8 s max by channel

POWER SUPPLY
(depending on model)

12-24 AC/DC + 10%
230 VAC  + 10%
115 VAC + 10%

PRODUCT COMPLIANCE

R&TTE:  1999/5/EC
EMC:  89/336/EEC
FCC:  47 CFR 15
IC:  RSS-210 ISSUE 5