JVC HM-HDS1EU Manual Do Utilizador
Masterpage:Right-2lineTitle0
EN
21
Filename [HDS1EU_2.fm]
Page 21
June 21, 2001 12:25 pm
SAT CONTROL SET (cont.)
T-V LINK
G
Check the result of the test.
If the satellite receiver’s channel number has not been
changed correctly ...
Press rt to move the highlight bar (pointer) to “NOT
CHANGED”, then press OK or e. Then perform the
procedure again from step
changed correctly ...
Press rt to move the highlight bar (pointer) to “NOT
CHANGED”, then press OK or e. Then perform the
procedure again from step
E.
NOTES:
● The Satellite Controller may not work with all types of satellite
receiver.
● For some satellite receivers, you need to set its channel input
mode to 2-digit.
● If your satellite receiver has more than two channel modes, be
sure to set to “All Channel Mode”. For details, refer to the
instruction manual of the satellite receiver.
instruction manual of the satellite receiver.
● When selecting the satellite receiver’s channel (
墌
step
F),
signals from the remote control may interfere with signals
transmitted from the Satellite Controller. In this case, move the
remote control as close to the recorder’s infrared beam
receiving window as possible.
transmitted from the Satellite Controller. In this case, move the
remote control as close to the recorder’s infrared beam
receiving window as possible.
T-V Link Functions
When you connect the recorder to your TV via a fully-wired
21-pin SCART cable (
21-pin SCART cable (
墌
pg. 12), the following functions are
available. You can use these functions only with a TV offering
T-V Link, etc.*
For details, refer to the instruction manual of your TV.
T-V Link, etc.*
For details, refer to the instruction manual of your TV.
* Compatible with TVs offering T-V Link, EasyLink, Megalogic,
SMARTLINK, Q-Link or DATA LOGIC via fully-wired 21-pin SCART
cable. The degree of compatibility and available functions may differ by
system.
cable. The degree of compatibility and available functions may differ by
system.
TV Auto Power On
The TV will turn on and be set to its AV mode automatically
whenever you play a tape.
For details, refer to the instruction manual of your TV.
whenever you play a tape.
For details, refer to the instruction manual of your TV.
VCR Auto Standby
You can use your TV’s remote control to turn off the recorder.
For details, refer to the instruction manual of your TV.
For details, refer to the instruction manual of your TV.
Direct Rec
You can easily start recording the programme that you are
watching on your TV. When you use this function, set “DIRECT
REC” to “ON” (
watching on your TV. When you use this function, set “DIRECT
REC” to “ON” (
墌
pg. 78).
If the satellite receiver’s
channel number has been
changed to the same one as
you set in step
channel number has been
changed to the same one as
you set in step
F ...
Press rt to move the
highlight bar (pointer) to
“CHANGED TO ...”, then
press OK or e to finish the
Sat Control Set mode.
highlight bar (pointer) to
“CHANGED TO ...”, then
press OK or e to finish the
Sat Control Set mode.
BRAND NAME
CODE
JVC
AMSTRAD
CANAL SATELLITE
CANAL +
D-BOX
ECHOSTAR
ECHOSTAR (VIA DIGITAL)
FINLUX
FORCE
GALAXIS
GRUNDIG
HIRSCHMANN
ITT NOKIA
JERROLD
KATHREIN
LUXOR
MASCOM
MASPRO
NOKIA
PACE
PANASONIC
PHILIPS
RFT
SAGEM
SALORA
SIEMENS
SKYMASTER
TPS
TRIAX
WISI
73
60, 61, 62, 63, 92
81
81
85
78, 79, 80
82
68
89
88
64, 65
64, 78
68
75
70, 71
68
93
70
87
65, 67, 74, 86, 92
74
66, 84
69
83
68
64
69
83
91
64
HDS1EU_.book Page 21 Thursday, June 21, 2001 12:30 PM