Manuais de utilizador para Adtran T1 CSU ACE

índice analítico

• Part Number 1203022L1

  1
• Document Number 61203022L1-1B

  1
• August 2004

  1
  • 1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.

    3
  • 1. This equipment complies with Part 68 of FCC rules. On the back of the equipment housing is a label showing the FCC registration number and ringer equivalence number (REN). If requested, provide this information to the telephone company.

    6
• Table of Contents

  15
• List of Figures

  17
• List of Tables

  19
• Chapter 1 General

  21
  • Unit Overview

    21
    • Figure 1. T1 CSU ACE Applications

      21
    • Figure 2. T1 CSU ACE Block Diagram

      22
  • Power Options

    23
    • Figure 3. T1 CSU ACE Power Supply

      23
  • Alarms

    24
    • Figure 4. T1 CSU ACE LED Alarms

      24
  • Loopback

    25
    • Table 1. Manual Loopbacks Switch Position Settings

      25
    • Figure 5. T1 CSU ACE Loopback Switch and LED

      26
  • Line Build Out

    26
    • Figure 6. Line Build Out Switch

      26
• Chapter 2 Installation

  27
  • Setting the LBO switch positions

    27
    • Table 2. Network LBO Switch Position Settings

      27
    • Table 3. Customer LBO Switch Position Settings

      27
  • Wallmounting the Unit

    28
    • Figure 7. Wallmounting the T1 CSU ACE

      29
  • Powering the Unit

    30
  • Connecting to The Network and CPE

    30
    • Table 4. Network RJ48C Connector Pin Assignments

      31
    • Table 5. CPE Connector Pin Assignments

      31
  • Test and Monitor Access

    32
    • Figure 8. T1 CSU ACE Bantam Jacks

      32
• Monitor Jacks

  32
• Break-and-Test Jacks

  33
  • Chapter 3 Troubleshooting and Maintenance

    35
    • Troubleshooting

      35
• Power

  35
  • 1. If locally powered, verify the power cable installation.

    35
  • 2. If the 12 V wall-mount power supply is used, check the supply’s cable and the circuit breaker for the 120 V receptacle the supply is plugged into.

    35
• Network LOS

  35
  • 1. Verify that the cable from the network demarcation is in NET modular jack on the bottom/end of the T1 CSU ACE.

    35
  • 2. If all connections seem intact, the far end CSU ACE can be looped back (using a BERT test set to send the LB code, or using MANUAL LB at the other end) to isolate the problem to the far end customer premises or the network.

    35
  • 3. If the problem persists after the LB has been activated, the problem appears to be within the network or the far end CSU ACE. In this case, notify the carrier.

    35
  • 4. If the problem disappears after loop-up, then the cause must be at the far end customer premises.

    35
• Equipment LOS

  36
  • 1. Verify that the cable from the CPE is in the CPE modular jack on the bottom/end of the CSU ACE.

    36
  • 2. If all connections seem intact, use a BERT test set in the NET IN and NET OUT jacks to test the CPE.

    36
• Power On - Self Check Failure

  36
• EPROM Checksum Failure

  36
  • Maintenance

    36
  • Chapter 4 Specifications

    37
    • Network and Customer Interface

      37
• Line

  37
• Data Rate

  37
• Signal Format

  37
• Output Amplitude

  37
• Network Connector Type

  37
• Customer Interface Connector Type

  37
  • LED Indicators

    37
• PWR

  37
• SYNC

  37
• Net LOS

  37
• NET MAN LB

  37
• NET RMT LB

  38
• EQ LOS

  38
• EQ MAN LB

  38
• EQ RMT LB

  38
  • Power

    38
• Local Power

  38
  • Environmental

    38
• Temperature

  38
• Relative Humidity

  38
  • Index

    39
  • A

    39
  • B

    39
  • C

    39
  • D

    39
  • E

    39
  • I

    39
  • L

    39
  • M

    39
  • N

    39
  • O

    39
  • P

    39
  • S

    39
  • T

    39
  • U

    40