Manual Do Utilizadoríndice analíticoSPECIFICATIONS1Regulatory Compliances1Agency Listings1Technical Specifications1GENERAL TROUBLESHOOTING2Contacting FARGO Technical Support2LCD Display Messages2Communications Errors2System does not meet requirements2A driver or application is conflicting with the FARGO driver2Using an inadequate data cable2Interference from an external device2Cannot print from application2Parallel port mode set incorrectly2Inadequate hard drive space2Card Feed Errors2are feeding improperly2Card is stalling on or at the feed rollers2Card jamming on the Flipper Table2Printer is unable to align flipper2Card feeds improperly off the Flipper Table2Encoding Errors2No ENC Response2No Mag Encoder2Mag Encode Failed2Card Jam: Mag2No Smart Encoder2Smart Encode Failed2Card Jam: Smart2Unable to read encoded data2Data intended for the magnetic stripe was printed on the card2Printing Process Errors2Aligning Ribbon Error2Print Ribbon2Print Ribbon Out2Wrong Print Ribbon2Head Lift2Printer pausing between panels2Printhead Temp2Printer Open2Transfer Process Errors2Transfer Film Drive Error2Laminator Cooling Error2Card Jam2Temperature Timeout2Transfer Lift2Output Errors2Cards feed into the Output Stacker, but are not lifted up into place2Diagnosing Image Problems2Pixel Failure2Card Surface Debris2Incorrect Image Darkness2Ribbon Wrinkle2Excessive Resin Printing2Incomplete Resin Printing2HDP Film Wrinkle2Incomplete Transfer2Image Placement2Poor Image Quality2Image Washout on Film2Registration problems2Image Skewed on the Card2PRINTER ADJUSTMENTS3Safety Messages3Fine Tuning the Card Separator Adjustment Assembly3Using FARGO HDP Technology to Print on Alternate Card Stocks3Device Options Tab3Ribbon Type3Color Matching3Resin Dither3Print Both Sides3Split 1 Set of Ribbon Panels3Print Back Side Only3Rotate Front 180 Degrees3Rotate Back 180 Degrees3Disable Printing3Buffer Single Card3Image Color Tab3Image Transfer Tab3Image Position3Transfer Dwell Time and Temperature3Flattener Temperature3K Panel Resin Tab3Defining an Area3Magnetic Encoding3Overview3Encoding Mode/ Coercivity/ Magnetic Track Selection3Magnetic Track Options3Verification3Shift Data Left3ISO Track Locations3Sending Track Information3Card Tab3Card Size3Card Type3Orientation3Copies3Test Print3About3Cleaning the Printer3Cleaning the Printhead3Cleaning the Platen Rollers3Clean the Inside of the Printer3Clean the Cleaning Rollers3PARTS REPLACEMENT4Removing the Covers4Print Station Cover4Front Transfer Cover4Rear Transfer Cover4Base Module Cover4Card Input Hopper Cover4Card Output Hopper Cover4Back Cover4Replacing the Control Panel Assembly Components4Replacing the Printhead Assembly Components4Printhead (D840854)4Fan Assembly (840134)4Head Force Spring (840272)4Ribbon Deflector (D840638)4Replacing the Print Station Components4O-Rings (140212)4Ribbon Sensor Board Assembly (140407)4Encoder Wheel (810492)4Ribbon Sensor Array Assembly (840108)4Ribbon Supply Motor Assembly (D840980)4Ribbon Take-Up Motor Assembly (D840980)4Headlift Motor Assembly (840131)4Ribbon Supply Encoder Sensor Assembly (D840982)4Headlift Sensor Assembly (D840983)4Replacing the Transfer Station Components4Film Drive O-Rings (140212)4Encoder Wheel (810492)4Stepper Motor Assembly (840123)4Lamination Supply Encoder Sensor Assembly (840135)4Lamination Take-Up Encoder Sensor Assembly (840136)4Lower Film Sensor Assembly (840199)4Upper Film Sensor Assembly (D841023)4Print Platen Roller (840319)4Transfer Peel Off Bar Assembly (840253)4Ribbon Drive Hub (840324)4Transfer Station Assembly (840152)4Lamination Assembly (840159)4Transfer Lift Switch (840142)4Transfer Lift Motor (840132)4Replacing Belt Driven Base Module Components4Drive Belt – Platen Roller to Card Feed Roller (220071)4Drive Belt – Card Feed Roller to Card Feed Roller (220082)4Stepper Motor Assembly (840164)4Compound Grooved Pulley (8402328)4Pinch Roller Spring Plate-Front (840354)4Pinch Roller Spring Plate-Back (840354)4Drive Belt – Tensioner to Platen Roller (F000003)4Drive Belt – Stepper Motor to Tensioner (F000004)4Main Pulley – Front (D850190)4Main Pulley – Back (D850190)4Belt (F000018)4Base Module (840151)4Replacing the Gear Driven Base Module Components4Drive Belt – Platen Roller to Card Feed Roller (220071)4Drive Belt – Card Feed Roller to Card Feed Roller (220082)4Stepper Motor Assembly (840164)4Pinch Roller Spring Plate - Front Input Side (840354)4Pinch Roller Spring Plate - Front Output Side (840354)4Pinch Roller Spring Plate - Back Output Side (840354)4Pinch Roller Spring Plate – Back Input Side (840354)4Main Pulley (D850190)4Gear – Card Transport (760330)4Compound Gear (D841032)4Base Module (840151)4Replacing the Card Input Hopper Components4Flipper Table Home Sensor Board Assembly (140407)4Card Low Sensor Board Assembly (140407)4Card Feed Belt (220082)4Cleaning Roller Drive Idler Gear (760401)4Card Feed Gear (810271)4Encoding Feed Motor Assembly (840100)4Cleaning Roller Assembly (840102)4Flipper Table Position Stepper Motor (840124)4Card Feed Motor Assembly (840198)4Clutch Spring (840285)4Card Sensor Assembly – Flipper Table (D840624)4Card Feed Sensor (D840625)4Magnetic Encoder Head (840104)4Encoder Card Sensor (140407)4Replacing the Power Assembly Components4Power Switch (120011)4Power Cord Receptacle (130067)4Main Print Board (A000030)4Lamination Board (140402)4Power Supply (150240)4Replacing the Output Stacker Components4Output Stacker (D840590)4Stacker Full Sensor (140407)4Stacker Lift Motor (840130)4PACKING YOUR HDP700 CARD PRINTER5BOARD LEVEL DIAGNOSTICS6Board Errors6EE Memory Error6EE Checksum Error6DRAM Memory Error6RAM Memory Error6FPGA6Update Firmware Now6Sensor Testing6LCD ON-LINE MENU NAVIGATION7Entering the LCD On-Line Menu and Selecting an Option7Print Test Image7Setup Printer7Preparing to adjust the Print Offset, Transfer TOF, and Transfer EOF7Adjusting the Transfer Tension7Aligning the Print Offset7Setting the Transfer TOF7Setting the Transfer EOF7Adjusting the Film Drive7Adjusting the Ribbon Tension7Adjusting the Ribbon Drive7Adjusting the Transfer Temperature7Setting the Flattener Temperature7Setting the Printhead Resistance7Adjusting the Image Darkness7Changing the Encoder Settings7Setting the Magnetic TOF7Adjusting the Flipper Offset7Show Error Count7Show Card Count7System Upgrade7Tamanho: 10 MBPáginas: 141Language: EnglishAbrir o manual