Manuais de utilizador para Vector 6SE70 VC

índice analítico

• Vector Control

  1
• Section 1: Parameterization of Base Drive

  1
• Section 2: Parameterization of Rectifier

  1
• Section 3: Simovis Trace Setup Method

  1
• Section 4: When Should a Drive be re-Tuned

  1
• We reserve the right to modify functions, technical data, standards, drawings and parameters.

  2
• We have checked the contents of this document to ensure that they coincide with the described hardware and software. However, deviations cannot be completely ruled-out, so we cannot guarantee complete conformance. However, the information in this docum

  2
• e-mail: mailto:drives.support@sea.siemens.com

  2
• Note:

  3
• Electrical equipment has parts an components which are at hazardous voltage levels.

  3
• Section 1:

  5
  • 5
    • 5
      • 5
        • 5
          • 5
            • 5
              • 5
                • Parameterization of Base Unit

                  5
• Vector Control

  5
• Power Section Definition

  7
  • Unit List

    8
  • 3 AC 200V to 230V

    8
    • 8
      • 8
        • 8
          • 6SE7021-1CA60

            8
• 1.2 Factory Reset

  15
• 1.3 Basic Start-up without Motor Connected to Load

  17
  • Connect External Wiring as connection diagram.

    20
  • Step 1: Dry set of contacts between terminals X101, pin#1 and pin#5 for Local/Remote Mode Selection. Jumper if not required.

    20
  • Step 3: Dry set of contacts between terminals X101, pin#1 and pin#9 for Source of Main Start/Stop Selection.

    20
  • Step 5: Dry set of contacts between terminals X101, pin#1 and pin#6 for Fixed Speed or Preset Speed Selection. Leave open if not required. Speed value is determined by P402. A selection of P402=100% will be a full speed reference setpoint.

    21
  • 1.3.2 Volts/Hz with Encoder

    22
    • P100 = 0

      22
    • P151 = ?

      22
  • Additional Connection for +15 Vdc Encoder.

    23
  • Step 10: Set Speed Reference to 20%.

    23
  • Step 11: Provide Start command. Note that if Signal A and Signal B are reversed, the motor will accelerate rapidly.

    23
  • Step 12: Connect the motor to the load, unless the plan is to change to Vector Control.

    23
  • 1.3.3 Vector Control without Encoder Feedback

    24
    • P100 = 3

      24
    • Wait

      24
    • Wait

      25
  • Step 10: Set Speed Reference to 20%, and monitor speed feedback r000, current feedback r004, and actual DC BUS r006. If stable increase speed in increments and continue to monitor feedbacks.

    25
    • P100 = 4

      26
    • P060 = 1

      26
    • Wait

      27
    • Wait

      27
  • Step 11: Set Speed Reference to 20%, and monitor speed feedback r000, current feedback r004, and actual DC BUS r006. If stable increase speed in increments and continue to monitor feedbacks.

    27
    • 33
      • 33
        • 33
          • 33
            • 33
              • 33
                • Parameterization of a Rectifer Unit

                  33
• Vector Control

  33
• Power Section Defintion

  33
• Factory Reset

  33
• Basic Start-up

  33
• Rectifier or Regen without auto-transformer

  33
• Regen with auto-transformer

  33
• 2.0 Power Section Definition

  35
  • Unit List

    36
  • 3 AC 380V to 460V

    36
    • 36
      • 36
        • 36
          • 6SE7038-2EH85-0AA0

            36
          • 6SE7041-0EH85-0AA0

            36
          • 6SE7041-3EK85-0AA0

            36
          • 6SE7041-8EK85-0AA0

            36
  • 3 AC 500V to 575V

    36
    • 36
      • 36
        • 36
          • 6SE7037-7FH85-0AA0

            36
          • 6SE7041-0FH85-0AA0

            36
          • 6SE7041-3FK85-0AA0

            36
          • 6SE7041-5FK85-0AA0

            36
          • 6SE7041-8FK85-0AA0

            36
          • 6SE7037-7HH85-0AA0

            36
          • 6SE7041-0HH85-0AA0

            36
          • 6SE7041-3HK85-0AA0

            36
          • 6SE7041-5HK85-0AA0

            36
          • 6SE7041-8HK85-0AA0

            36
  • 3 AC

    37
  • 3 AC

    37
  • 3 AC

    38
• 2.1 Factory Reset

  39
• 2.2 Basic Start-up (Regenerative Rectifier without Autotransformer)

  41
  • 41
    • P052 = 5

      41
    • P071 = 460

      41
  • Connect External Wiring as connection diagram.

    43
  • Step 1: Dry set of contacts between terminals X101, pin#6 and pin#13 for Local/Remote Mode Selection. Jumper if not required.

    43
  • Step 3: Dry set of contacts between terminals X101, pin#6 and pin#9 for Source of Main Start/Stop Selection.

    43
• 2.3 Basic Start-up (Regenerative Rectifier with Autotransformer)

  45
  • 45
    • P052 = 5

      45
    • P071 = 460

      45
• Vector Control

  47
• Vector Control

  55
• 4.0 Conditions that would merit re-tuning the drive

  57
  • If tuning parameters P103, P116, P120, P223, P235, P236, P240 and P471 had been recorded prior to the CUVC card being replaced.

    57