Справочник Пользователя для American Dryer Corp. AD-464
450260-1
www.amdry.com
19
Tilting Piston Replacement
1. Disconnect compressed air supply from the dryer.
2. Tilt, then level the dryer to exhaust as much air as
2. Tilt, then level the dryer to exhaust as much air as
possible.
3. Disengage EMERGENCY STOP (E-Stop). Discontinue
electrical power to the dryer.
4. Remove the six (6) screws holding the piston cover plate.
5. Label the air lines as an aid when reconnecting.
6. Loosen the 3/8 compression fittings.
7. Remove the air lines.
8. Remove the 3/8 straight connector.
9. Remove the 3/8 elbow.
5. Label the air lines as an aid when reconnecting.
6. Loosen the 3/8 compression fittings.
7. Remove the air lines.
8. Remove the 3/8 straight connector.
9. Remove the 3/8 elbow.
10. Carefully remove the E-clips from the clevis pins.
11. Remove clevis pins.
12. Loosen the bottom setscrew in the piston rod eye.
13. Unscrew the piston rod eye from the tilting piston.
14. To install new tilting piston, reverse above procedure
13. Unscrew the piston rod eye from the tilting piston.
14. To install new tilting piston, reverse above procedure
(Step #12 through Step #1).
MAN5278
MAN3483
7. Remove the two (2) 1/4-20 hex head bolts that mount
the solenoid valve. (Refer to the illustration on the top
right of page 18.)
8. Remove the three (3) 3/8 straight connectors. (Refer to
the illustration on the top right of page 18.) Reinstall
these connectors on the new solenoid valve body.
9. Remove the two (2) 3/8 mufflers. (Refer to the
illustration on the top right of page 18.) Reinstall these
mufflers on the new solenoid valve body.
10. The left orifice (marked #12 on the tilting solenoid valve)
now must be configured for external pilot.
Note
For 1-way tilt models proceed to Step #23.
11. Remove the two (2) Phillips head screws.
12. Carefully remove the end of the valve.
Note
The pieces within the end of the valve are small.
Handle carefully to avoid losing parts.
13. Place the solenoid plug over the pilot orifice position of
the solenoid valve end.
14. Place the O-Ring (from Step #13) into the top portion of
the solenoid valve end.
15. Place end back onto the valve removed in Step #13.
16. Replace the two (2) Phillips head screws removed in
16. Replace the two (2) Phillips head screws removed in
Step #12.
17. Remove Allen plug on the left side of the orifice marked
#12 on the tilting solenoid valve.
18. Remove the pilot airs 1/4 compression fitting.
19. Remove the pilot airs 1/8 elbow. Reinstall the elbow
19. Remove the pilot airs 1/8 elbow. Reinstall the elbow
onto the new solenoid valve body.
20. Reconnect the three (3) air lines removed in Step #7.
Tighten/secure compression fittings on the air lines
loosened in Step #7.
21. Bolt the solenoid valve in place using the two (2)
1/4-20 hex head bolts removed in Step #8.
22. Reconnect the three (3) air line compression fittings.
23. Reestablish the compressed air supply to the dryer.
24. Check for leaks.
25. Reestablish electrical power to the dryer.
26. Engage EMERGENCY STOP (E-Stop) disengaged in
23. Reestablish the compressed air supply to the dryer.
24. Check for leaks.
25. Reestablish electrical power to the dryer.
26. Engage EMERGENCY STOP (E-Stop) disengaged in
Step #3.
!
!