Справочник Пользователя для Hotpoint ACC9 BF7

• Place your dryer at a distance 

from gas ranges, stoves, 

heaters, or cooktops because 

flames can damage the 

appliance.

If you are going to install the 

appliance under a work counter, 

be sure to leave a 10 mm 

space between the top and any 

other objects on or above the 

machine and a 15 mm space 

between the sides and lateral 

furnishings or walls. This is to 

ensure proper air circulation.

• When the dryer is in use, there has to be adequate 

ventilation. Make sure you put your dryer in an environment 

that is not damp and has proper air circulation throughout. 

Airflow around the dryer is essential to condense the water 

produced during the washing, the dryer will not operate 

efficiently in an enclosed space or cupboard.

 If using the dryer in a small or cold room some 

condensation will be experienced.

 We do not recommend that the dryer is installed in a 

cupboard but the dryer must never be installed behind a 

lockable door, a sliding door or a door with a hinge on the 

opposite side to that of the dryer door.

If the machine is positioned close to a drain it is possible 

to drain the condensed water directly without using the 

waterbottle. In which case it is no longer necessary to empty 

the water bottle at the end of each cycle.If the Dryer is 

positioned above or close to a Washing Machine the same 

drainage can be used. Just unlink the tube indicated in figure 

A and connect it to the drainage.

If the drainage is further away than the length of the tube it 

is possible to buy and connect a tube of the same diameter 

and the necessary length  in order to reach the drainage.

To install the new tube just substitute the existing one as 

indicated in figure B inserting it in the same place.

 The drain tube has to be below 1 m from the bottom of 

the Dryer.

 Once the Dryer has been installed please assure that 

the drain tube is not bent or contorted.

10 m

m

15 mm

15 mm

Make sure of the following before you insert the plug into the 

electrical socket:
•  Ensure your Hands are dry. 

•  The socket must be grounded. 

•  The socket must be able to sustain the machine’s maximum 

power, which is indicated on the rating plate (see Dryer Description). 

•  Power voltage must be within the values indicated on the 

rating label (see Dryer Description). 

•  The socket must be compatible with the dryer’s plug. Should 

this not be the case, replace the plug or the socket. 

 Do not use extension cords. 

 The dryer must not be installed outdoors, even if the space is 

sheltered. It can be very dangerous if exposed to rain or storms. 

 Once installed, the dryer’s electrical wire and plug must be 

within reach. 

 The power cord must not be bent or squashed. 

 The power cord is supplied fitted with a BS1363 plug and with 

a 13 amp BS1362 fuse. If it is necessary to fit a replacement 

fuse, it must be a 13 Amp ASTA approved to BS1362 type. 

WARNING: The plug must not be used without a fuse cover. 

If a replacement fuse holder/cover is required, it must be of the 

same colour coding or wording as shown on the base of the plug. 

Replacements are available from authorised dealers. 

Changing the plug  

The wires in the power cord are coloured in accordance with 

the following.

 If the plug being replaced is a non-rewirable type, then the 

cut-off plug must be disposed of safely. DO NOT leave it where 

it can be inserted into a socket and create a shock hazard. 

 The power cord should be checked periodically and replaced 

by a cord specially prepared for this dryer and fitted only by 

authorized technicians (see Service). New or longer power 

cords are supplied at an extra charge by authorized dealers. 

 The manufacturer denies any responsibility should any of 

these rules not be followed.

 If in doubt about any of the above consult a qualified 

electrician.

Once you’ve installed your dryer and before you use it, clean 

the inside of the drum to remove any dust that could have 

accumulated during transportation.

Moulded plug

GREEN &
YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR
CORD GRIP

Green and Yellow (Earth) 

wire to terminal marked “E”, 

symbol x, or coloured green 

and yellow.

Blue (Neutral) wire to 

terminal marked ”N” or 

coloured black.

13A ASTA approved fuse to 

BS 1362.

Brown (live) wire to teminal 

marked “L” or coloured red.

2

H<1m

2

Fig. A

Fig. B