Справочник Пользователя для Pelco SB19-1/SB1901
Pelco Manual C467M-D (5/95)
5
7.
Slide the back box through the ceiling tile and
mounting plate and replace the four (4) 1/4-20 bolts
and tighten to secure the back box to the mounting
plate.
mounting plate and replace the four (4) 1/4-20 bolts
and tighten to secure the back box to the mounting
plate.
8.
Check the alignment of the back box to the ceiling
tile by attaching the 12.5" round faceplate trim to
the bottom of the back box, aligning the two studs
with two of the holes in the flanges of the back
box and engaging the studs. The studs should en-
gage, while leaving a very minimal gap between
the ceiling and faceplate trim. Loosen the 1/4-20
hardware in the sides of the back box and make
adjustments as required. Insure that the face of the
back box is level with the ceiling.
tile by attaching the 12.5" round faceplate trim to
the bottom of the back box, aligning the two studs
with two of the holes in the flanges of the back
box and engaging the studs. The studs should en-
gage, while leaving a very minimal gap between
the ceiling and faceplate trim. Loosen the 1/4-20
hardware in the sides of the back box and make
adjustments as required. Insure that the face of the
back box is level with the ceiling.
9.
Attach the lens and camera head to the tilt table
(hardware not supplied), if not factory pre-assembled,
using the camera/lens position template supplied
as a guide (see Figure 3). Locate the lens and cam-
era so that when the notched area in the template
is fitted under the tilt table, the lens and camera do
not project further out from the tilt table than al-
lowed by the template. Also, the lens must not
project higher than the long end of the template.
(hardware not supplied), if not factory pre-assembled,
using the camera/lens position template supplied
as a guide (see Figure 3). Locate the lens and cam-
era so that when the notched area in the template
is fitted under the tilt table, the lens and camera do
not project further out from the tilt table than al-
lowed by the template. Also, the lens must not
project higher than the long end of the template.
NOTE: If the camera and lens do not fit within
the boundaries of the template, they will not fit
inside the dome and need to be replaced with
smaller units.
the boundaries of the template, they will not fit
inside the dome and need to be replaced with
smaller units.
10. Mount the camera power supply onto the bracket
provided, if not factory pre-assembled. (Screws to
mount the camera power supply and lens are not
provided with the pan/tilt.)
mount the camera power supply and lens are not
provided with the pan/tilt.)
NOTE: For PC1804B and PC900U cameras,
remove the mounting bracket with the two 1/4-
20 holes in it from the camera’s power supply,
align the camera power supply so that the two
(2) threaded holes in the power supply align
over two of the round holes in the camera power
supply bracket on the pan/tilt, and attach it with
the screws provided with the camera.
remove the mounting bracket with the two 1/4-
20 holes in it from the camera’s power supply,
align the camera power supply so that the two
(2) threaded holes in the power supply align
over two of the round holes in the camera power
supply bracket on the pan/tilt, and attach it with
the screws provided with the camera.
11. Hook up camera power, video, and lens with the
connectors supplied, if not factory pre-assembled.
Coil the excess camera cable and tie it down with
tie-wraps to the pan/tilt body.
Coil the excess camera cable and tie it down with
tie-wraps to the pan/tilt body.
NOTE: To insert or remove the drive unit from
the back box, the drive unit may need to be ro-
tated 90
the back box, the drive unit may need to be ro-
tated 90
° so that the wiring cover and/or cam-
era power supply does not interfere with the
side of the back box. If difficulty inserting or
removing the drive unit is experienced, slowly
and gently rotate the drive unit 90
side of the back box. If difficulty inserting or
removing the drive unit is experienced, slowly
and gently rotate the drive unit 90
°.
12. Engage the connector of the coil cord into the con-
nector of the pan/tilt and attach the safety clamp;
then insert the pan/tilt into the back box, feeding
the coil cord back through the opening in the top
of the back box. Position the pan/tilt in the back
box so that the horizontal studs in the pan/tilt mount
bracket align with the slots in the back box mount
bracket. Lift the pan/tilt until it reaches its stop,
then slide it to one side while letting it drop about
1/4 inch (see Figure 4).
then insert the pan/tilt into the back box, feeding
the coil cord back through the opening in the top
of the back box. Position the pan/tilt in the back
box so that the horizontal studs in the pan/tilt mount
bracket align with the slots in the back box mount
bracket. Lift the pan/tilt until it reaches its stop,
then slide it to one side while letting it drop about
1/4 inch (see Figure 4).
Figure 3. Camera/Lens Mounting Dimensions
6.5
(16.51)
MAX
1.625
(4.13)
(4.13)
MAX
.875
(2.22)
MAX
TILT TABLE
CAMERA
LENS
SUPPLIED
TEMPLATE
3.25
(8.26)
MAX
GENERAL LENS MAXIMUM EXTENSIONS
PAST EDGES OF TILT TABLE
PAST EDGES OF TILT TABLE
NOTE: VALUES IN PARENTHESE ARE CENTIMETERS;
ALL OTHERS ARE IN INCHES