Справочник Пользователя для Majestic Appliances UVS36RN
12
UVS33/36 Vent-Free Heaters
20002211
First Firing
Upon completing your gas line connection, a small
amount of air will be in the lines. When first lighting
unit with pilot light, it will take a few minutes to purge
themselves of this air. Once the purging is complete,
the pilot and burner will light and operate as indicated
in the instruction manual. Subsequent lightings of the
heater will not require such purging.
amount of air will be in the lines. When first lighting
unit with pilot light, it will take a few minutes to purge
themselves of this air. Once the purging is complete,
the pilot and burner will light and operate as indicated
in the instruction manual. Subsequent lightings of the
heater will not require such purging.
Odor During Operation
Neither natural gas nor propane gas give off an odor
when burned. The nature of a vent free combustion
system, however, is such that odors may occasionally
be produced during heater operation when impurities
exist in the immediate area. Cleaning solutions, paint,
solvents, cigarette smoke, candles, adhesives, new car-
pet or textiles, etc., all can create fumes. These fumes
may mix with combustion air and can create odor. Such
odors will disappear over time, however, the condition
can be alleviated by opening a window or otherwise
providing additional ventilation to the area.
when burned. The nature of a vent free combustion
system, however, is such that odors may occasionally
be produced during heater operation when impurities
exist in the immediate area. Cleaning solutions, paint,
solvents, cigarette smoke, candles, adhesives, new car-
pet or textiles, etc., all can create fumes. These fumes
may mix with combustion air and can create odor. Such
odors will disappear over time, however, the condition
can be alleviated by opening a window or otherwise
providing additional ventilation to the area.
Flame Adjustment
For fireplaces equipped with HI/LO valves, flame ad-
justment is accomplished by rotating the HI/LO adjust-
ment knob located near the center of the gas control.
(Fig. 18)
justment is accomplished by rotating the HI/LO adjust-
ment knob located near the center of the gas control.
(Fig. 18)
Log Installation UVS36
1. Remove window frame. (See "Window
Frame" section)
2. Remove logs from packaging.
As with all plastic - these
are not toys and should be
kept away from children and
infants.
are not toys and should be
kept away from children and
infants.
3. Place rear log (BE8) on rear bracket
(ensure log is seated properly, leveled
and centered to the unit), so the log
will not move form side to side and is
firmly positioned onto the bracket.
and centered to the unit), so the log
will not move form side to side and is
firmly positioned onto the bracket.
4. Place front left log (BE6) on top of
burner, left side. Use log's bottom
holes to locate it onto the left bracket
log locator studs.
holes to locate it onto the left bracket
log locator studs.
5. Place front right log (BE7) on top of
burner right side. Use log's bottom
holes to locate it onto the left bracket
log locator studs.
holes to locate it onto the left bracket
log locator studs.
6. Place ember material on top of burner.
(Refer to "Ember Material Placement").
7. Place top left log (BE9) onto locator notches. Ensure
log is secure.
8. Place top right log (BE10) onto locator notches.
Ensure log is secure.
Ember Material Placement
Separate the ember material into small pieces and
place onto the burner in front of the front logs. Do NOT
pack down, leave in fluffy, loose condition for most re-
alistic ember effects. Do not install more embers on
the burner than come with the unit.
Application of excess loose material may adversely
affect performance of theheater.
Replacement loose embers must be purchased
through authorized Majestic Fireplaces dealers.
place onto the burner in front of the front logs. Do NOT
pack down, leave in fluffy, loose condition for most re-
alistic ember effects. Do not install more embers on
the burner than come with the unit.
Application of excess loose material may adversely
affect performance of theheater.
Replacement loose embers must be purchased
through authorized Majestic Fireplaces dealers.
WARNING: All previously applied loose
material must be removed prior to reappli-
cation.
material must be removed prior to reappli-
cation.
Lava Rock
The lava rock provided with this fireplace must be
placed on the firebox bottom on either side of the
burner assembly. Do not place lava rock directly on
burner. (Fig. 18)
placed on the firebox bottom on either side of the
burner assembly. Do not place lava rock directly on
burner. (Fig. 18)
Under no circumstances should this lava
rock be placed on any part of the burner
assembly.
assembly.
�����
����������
�����
����������
�����
Front Left Log
(BE6)
Rear Log
(BE8)
Top Right Log
(BE10)
Top Left Log
(BE9)
Front Right Log
(BE7)
LG131
Fig. 18 UVS36 log placement.