Справочник Пользователя для Alliance Laundry Systems F232182R1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming
17
F232182
When modifying a cycle, a time must be entered for
each segment. To skip a segment or spin, set the time
to “00” and press the Start key. Table 3 gives the time
parameters for each segment and spin, as well as the
allowable temperature range.
each segment. To skip a segment or spin, set the time
to “00” and press the Start key. Table 3 gives the time
parameters for each segment and spin, as well as the
allowable temperature range.
Table 3
NOTE: Spin times in cycle segments 1 – 10 are
entered in seconds (30 to 240), and time for final
spin in segment 11 is entered in minutes (1 to 10).
entered in seconds (30 to 240), and time for final
spin in segment 11 is entered in minutes (1 to 10).
1. Press the Up key until the computer display
shows the segment to be edited. Press the Start
key.
key.
2. Use the Up or Down key to select the desired
segment time. Set this value to zero to skip the
segment. Press the Start key.
segment. Press the Start key.
NOTE: The computer does not count down the
remaining cycle time during fills, drains, cool-
down, or prior to first achieving the programmed
heat temperature when heating. The computer
resumes counting down cycle time once the
programmed fill level is reached, when the machine
has drained, and after a programmed heat
temperature is reached.
remaining cycle time during fills, drains, cool-
down, or prior to first achieving the programmed
heat temperature when heating. The computer
resumes counting down cycle time once the
programmed fill level is reached, when the machine
has drained, and after a programmed heat
temperature is reached.
3. If the temperature-controlled fill setup option is
enabled, the display will show “tFIL.” Press the
Start key.
Start key.
4. Use the Up or Down key to select the desired fill
temperature. Refer to Table 4 for fill options.
Table 4
If the temperature-controlled fill setup option is
enabled and a target temperature is set, the
selected fill valve(s) will energize for the first
three seconds of the segment fill. The computer
will then begin operating the fill valves in an
attempt to reach the target temperature. Press the
Start key.
enabled and a target temperature is set, the
selected fill valve(s) will energize for the first
three seconds of the segment fill. The computer
will then begin operating the fill valves in an
attempt to reach the target temperature. Press the
Start key.
5. Use the Up or Down key to select the desired fill
level. Refer to Table 5.
Table 5
Time and Temperature Parameters
Function
Minimum
Maximum
PreWash
2 minutes
30 minutes
Wash
2 minutes
20 minutes
Fill 1
2 minutes
15 minutes
Fill 2
2 minutes
15 minutes
Fill 3
2 minutes
15 minutes
Fill 4
2 minutes
15 minutes
Fill 5
2 minutes
15 minutes
Fill 6
2 minutes
15 minutes
Fill 7
2 minutes
15 minutes
Fill 8
2 minutes
15 minutes
Fill 9
2 minutes
15 minutes
Intermediate Spin*
30 seconds
240 seconds
Final Spin**
1 minute
10 minutes
Temperature
75°F (25°C)
200°F (93°C)
* Programmed with wash segment through Fill 8.
** Programmed with Fill 9.
** Programmed with Fill 9.
Fill Temperature Options
Display
Fill Type
CFIL
Cold Fill
HFIL
Hot Fill
bFIL
Warm Fill
AFIL
Auxiliary Fill*
*This is available only if the “SUP5”/“AFIL” setup
option is set to “AFIL.”
Water Level Options
Display
Fill Level
Lo
Low Level
n
Ed
Medium Level
HI
High Level