Справочник Пользователя для Vermont Casting 20DVT

3

This gas appliance should be installed by a qualified 
installer in accordance with local building codes and with 
current CSA-B149.1 Installation codes for Gas Burning 
Appliances and Equipment. For USA Installations follow 
local codes and/or the current National Fuel Gas Code. 
ANSI Z223.1/NFPA 54.
In the Commonwealth of Massachusetts, all gas fitting 
and installation of this heater shall only be done by a 
licensed gas fitter or licensed plumber.
FOR SAFE INSTALLATION AND OPERATION PLEASE 
NOTE THE FOLLOWING:

1.  This fireplace gives off high temperatures and should be 

located out of high traffic areas and away from furniture and 
draperies.

2.   Children and adults should be alerted to the hazards of high 

surface temperatures of this fireplace and should stay away 
to avoid burns or ignition of clothing.

3.   CAUTION: Due to high glass surface temperature chil-

4.   Under no circumstances should this fireplace be modified. 

Parts removed for servicing should be replaced prior to 
operating this fireplace again.

5.  Installation and any repairs to this fireplace must be per-

formed by a qualified installer, service agency or gas sup-
plier. A professional service person should be contacted to 
inspect this fireplace annually. Make it a practice to have 
all of your gas fireplaces checked annually. More frequent 
cleaning may be required due to excess lint and dust from 
carpeting, bedding material, etc.

6.  Control compartments, burners and air passages in this fire-

place should be kept clean and free of dust and lint. Make 
sure the gas valve and pilot light are turned off before you 
attempt to clean this fireplace.

7.  The venting system (chimney) of this fireplace should be 

checked at least once a year and if needed your venting 
system should be cleaned.

8.  Keep the area around your fireplace clear of combustible 

materials, gasoline and other flammable vapor and liquids. 
This fireplace should not be used as a drying rack for cloth-
ing, nor should Christmas stockings or decorations be hung 
on or around the fireplace.

9.  Under no circumstances should any solid fuels (wood, coal, 

paper or cardboard etc.) be used in this fireplace.

10. The flow of combustion and ventilation air must not be ob-

structed in any way.

11. When fireplace is installed directly on carpeting, vinyl tile 

or any combustible material other than wood, the fireplace 
must be installed on a metal or wood panel extending the 
full width and depth of the fireplace.

12. This fireplace requires adequate ventilation and combustion 

air to operate properly. 

13. This fireplace must not be connected to a chimney flue 

serving a separate solid fuel burning fireplace.

14. When the fireplace is not in use it is recommended that the 

gas valve be left in the OFF position.

A) Flat on wall  

B) Cross corner 

C)  **Island

D) *Room divider  E) *Flat on wall corner 

F)  Chase installation

Y) 6” minimum

NOTE: (fig. 1) 
** Island (C) and Room Divider (D) installation is possible as 
long as the horizontal portion of the vent system (X) does not 
exceed 20’ (610 cm).  See details in Venting Section.
*  When you install your fireplace in(D) Room divider or (E) Flat 
on wall corner positions (Y), a minimum of 6” (153 mm) clear-
ance must be maintained from the perpendicular wall and the 
front side edge of the fireplace.
Refer to (Y) in Figure 1.

Remove any plastic from trim parts before turning the 
fireplace ON.
It is normal for fireplaces fabricated of steel to give off 
some expansion and/or contraction noises during the 
start up or cool down cycle. Similar noises are found 
with your furnace heat exchanger or car engine.
It is not unusual for your gas fireplace to give off some 
odor the first time it is burned. This is due to the curing of 
the paint and any undetected oil from the manufacturing 
process. 
Please  ensure  that  your  room  is  well  ventilated  - 
open all windows.
It is recommended that you burn your  fireplace for at 
least ten (10) hours the first time you use it. If the optional 
fan kit has been installed, place the fan switch in the 
“OFF” position during this time.

LU584-1
Locating unit
2/4/99   djt

LU584-R

Fig. 1  Locate gas fireplace.

This appliance may be installed in an aftermarket per-
manently located, manufactured home or mobile home, 
where not prohibited by local codes.
This appliance is only for use with the type of gas indicat-
ed on the rating plate. This appliance is not convertible 
for use with other gases, unless a certified kit is used.