Справочник Пользователя для Toshiba RAV-SM1400UT-E
53
HO
W T
O
ADJUST
AIR
DIRECTION
•
N
e
v
er mo
v
e
the flap (Air direction up/do
wn adjusting plate) which is oper
ated on the remote
controller with hands e
xcept a case of cleaning of the flap
.
•
While the unit stops
, the flap (Air direction up/do
wn adjusting plate) directs do
wnw
ard auto-
matically
.
•
Dur
ing prepar
ation of heating, the flap (Air direction up/do
wn adjusting plate) directs upw
ard.
The s
winging oper
ation star
ts after heating preparation status has been cleared.
Ho
we
v
e
r,
s
winging is displa
y
ed on the A
U
T
O
flap displa
y of the remote controller e
v
en if the heating
oper
ation is being prepared.
H
o
w to set up the air direction
Ev
e
ry pushing
b
utton dur
ing oper
ation, the air direction changes
.
H
o
w to star
t s
winging
When pushing
b
utton, set the direction of the flap (Air direction up/do
wn adjusting plate) to
the lo
w
est position, and then push
b
utton again, the s
winging is displa
y
ed and the air direction
automatically changes upw
ard/do
wnw
ard.
H
o
w to stop s
winging
Pushing
b
utton once again dur
ing s
winging of the flap stops the flap at the desired position.
Then, when pushing
b
utton, the air direction can be set to position from the upper
most
position.
•
In cooling or dr
y oper
ation, the flap does not stop when the flap directs downw
ard.
If doing so
, the flap stops at the 3
rd
position from the upper
most position.
In heating operation
Direct the flap (Air direction up/do
wn adjusting plate) do
wn-
w
ard, otherwise the hot air ma
y not reach at the f
oot.
In cooling/dr
y operation
Direct the flap (Air direction up/do
wn adjusting plate) upw
ard,
otherwise de
wdrops ma
y adhere or dr
ip do
wn to near of the
discharge g
rille
.
In air
b
lo
wing operation
In all
operation modes
Displa
y when s
winging stopped
Initial setup
Initial setup
Initial setup
Series of
operation
F
an/Heat operation
Cool/Dr
y operation
SLIDE SWITCH
•
Do not change setting of the slide s
witch because a malfunction occurs b
y
other settings
.
•
Bef
ore usage
, chec
k the slide s
witch is set to the position as f
ollo
ws;
HO
W T
O
INSER
T THE
B
A
TTERIES
1.
Holding the both sides of the co
v
er and remo
v
e
it b
y
sliding do
wnw
ard.
2.
Correctly inser
t 2 AAA alkali batter
ies matching + and - polar
ities with indications
.
3.
Push RESET b
utton with something tipped and attach the co
v
e
r.
•
Replace the batter
ies when the displa
y section of the remote controller is difficult to be read,
or when the signal cannot be sent if y
ou are not close to the sensor
.
(The standard replacement time of the alkali batter
ies is appro
x.
one y
ear
.)
•
Use the same type of ne
w batter
ies f
or replacing tw
o batter
ies
.
•
In case when y
ou do not the remote controller
for a long time
, remo
v
e
the batter
ies
.
RESET b
utton
Cov
er
SK
N
AH
C
SK
N
AH
C
Remo
v
al of batter
y co
v
e
r
Operation mode displa
y
of remote controller
Slide s
witch position
Swing
Slide s
witch position
Flashing position
on remote controller
Corresponding model
for change of flap
HIGH
MED
.