Справочник Пользователя для Toshiba RAV-SM1400UT-E

54

•

Direct the tr

ansmitter of the remote controller to

w

ard the sensor (indoor unit body).

When the signal is nor

mally receiv

ed, 

“Pi

” sound is heard once

.

(“

Pi, pi

” sounds are heard only when the oper

ation has star

ted.)

•

The standard distance which the signal can be receiv

ed is appro

x.

 7m.

The distance diff

ers a little according to the capacity of the batter

y,

 etc.

•

Be careful there is not something to b

loc

k the signal between the sensor (indoor unit body)

and the remote controller

.

•

Do not put the remote controller on the place e

xposed to the direct sunlight or air from the air

conditioner or near the sto

v

e

, etc.

•

Do not drop

, thro

w

, or clean with w

ater the remote controller

.

•

The signal ma

y be accepted in a room where the electronic instantaneous-ON type or

in

v

e

rter type florescent light is set.

 F

or details

, contact the shop which y

ou purchased the air

conditioner

.

•

Chec

k a signal is receiv

ed correctly b

y

 pushing 

 Star

t/Stop b

utton at the position to be

fix

ed.

•

T

o

 tak

e off remote controller

, pull it to

w

ard y

ou.

Be sure to set the remote controller in the same room where the sensor (indoor unit) is

installed.

When a signal is correctly receiv

ed, 

“Pi

” sound can be heard.

Mounting scre

w

T

russ tapping

Put on.

Push.

Fix the remote controller 

holder with the scre

ws.

Setting method of 

remote controller

Remote controller holder

When pushing 

ADR

 b

utton on the remote controller

, the present address is displa

y

ed on the

displa

y section of the remote controller

. If this address matches with the address of the sensor

(inside of panel or indoor unit), a b

uzz

er sounds

.

(When ALL is displa

y

ed, b

uzz

er sound is necessar

ily heard.)

When ALL is displa

y

ed, the air conditioner can be oper

ated regardless of an

y address of the

sensor (inside of the indoor unit).

 Send the signal b

y

 directing the remote controller to

w

ard the

sensor (panel or indoor unit body) to be handled.

Setup to remote controller address

1.

When k

eeping 

ADR

 pushed f

or 4 seconds or more

, 

ADR

 lamp goes on at the displa

y

section of the remote controller and the present address is displa

y

ed with flashing.

2.

Ev

er

y pushing 

ADR

, the address is e

xchanged as ALL 

 1 

 2 

 3 

…

 

 6 

 ALL.

 Match

one of them with the address s

witch of the indoor unit sensor to be handled.

3.

When pushing 

C L

, the address displa

y goes on and is displa

y

ed f

or 5 seconds

.

If the address matches with the address s

witch of the oper

ation par

t, the b

uzz

er sounds

.

S001

4

–

6

S002

3 6

2 5

1 4

Address 

select

Address

S002

3 6

2 5

1 4

Address

S002

3 6

2 5

1 4

Address

S001

4

–

6

Address 

select

S001

4

–

6

Address 

select

Displa

y of 

remote 

controller 

address

Address s

witch 

position of 

sensor

*

Address s

witch 

of sensor unit 

can be set an

y 

position.

Address

Address

Address

Address

1

–

31

–

3

1

–

3

T

u

rn

 the knob to the r

ight side f

or 1 to 3 while to the left side f

or 4 to 6 of Address select s

witch

S001.