Справочник Пользователя для Shark EP710

To reduce the risk of electric 

shock, the power cord must be 

disconnected before removing the dust 

cup, dust cup filter,changing the filters or 

performing maintenance/trouble shooting 

checks.
The exhaust filter is located on the 

front of the unit below where the dust 

cup is. 

1. Check the exhaust filter frequently 

and clean when dirty.

2. Press inward on each side of the 

exhaust filter cover and pull out to 

remove from the vacuum cleaner.

3. Remove the exhaust filter.

4. Rinse in lukewarm water and dry 

the filter completely before re-

installing into the vacuum. Do not 

use a washing machine to rinse the 

filter. Do not use a hair dryer to dry 

it. Air dry only. Never operate the 

vacuum without the filters in place.

5. When the filter is dry, replace into 

the vacuum and replace the filter 

cover.

Note: A severely soiled or clogged 

filter should be thoroughly washed with 

fresh tepid water. A mild detergent can 

be used if required.

To reduce the risk of electric 

shock, the power cord must be 

disconnected before removing the dust 

cup, dust cup filter,changing the filters or 

performing maintenance/trouble shooting 

checks.
The dust cup can be washed in 

lukewarm water. Do not use strong 

detergents. Ensure that the dust cup is 

fully dry before putting back on the 

vacuum cleaner.  (Fig. 16) Do not wash 

in dishwasher.  

Fig. 16

Motor Thermostat
Important:  

This motor is equipped 

with a motor protective thermostat.  If 

for some reason the vacuum cleaner 

should overheat,  the thermostat will 

automatically turn the unit off.  Should 

this occur:

•

Push the On/Off button once.

• Disconnect the plug from the 

power source.

• Check the source of overheating 

problem. (i.e. clogged hose or 

filter)

• if clogged hose or filter is found, 

unclog the hose and replace the 

filters.

• Wait at least 30 minutes before 

attempting to reuse the vacuum.

• After unit has cooled down for 

30 minutes, plug in the cleaner 

and push the On/Off button. The 

vacuum should start again.

• If the vacuum still does not start, 

contact EURO-PRO at 1-800-

798-7398.

8

Occasionally the power nozzle drive 

belt will require changing, the 

frequency will depend upon the amount 

of use your vacuum sees.

1. Turn the vacuum "Off" and unplug 

from power supply.

2. Release the handle by pressing on 

the handle release pedal and pull 

back on the handle until it releases 

from its upright position. Then turn 

the vacuum over and place on the 

floor.

3. With a Phillips #2 screw driver 

remove the five screws on the 

bottom plate. (Fig. 17)

Fig. 17

4. Carefully remove any residue that 

may exist in the belt area.

5. If the belt has broken, remove any 

loose pieces before replacing.

6. Hold the agitator with your hand. If 

the belt is still attached to the 

agitator, there will be tension on it.

7. Carefully lift the left side of the 

agitator and then the right side.

8. Remove the worn or broken belt 

from the motor drive shaft.

9. Loop the new belt first over the 

drive shaft and then over the belt 

pulley on the agitator. (Fig. 18)

10. Insert the right side of the agitator in 

first by placing the rounded portion 

of the end cap down into the slot 

and then do the same with the left 

side. Press firmly to make sure that 

each end is completely inserted.

11. Check to make sure that the belt is 

centered on the belt pulley and that 

the agitator turns freely.

12. Replace the bottom plate over the 

power head base and screw firmly.

Fig. 18

: Always disconnect from 

power source when servicing or 

cleaning the unit. Failure to do so could 

result in electrical shock or personal 

injury from cleaner suddenly starting.

• Turn unit “Off” and unplug from 

wall outlet. 

• Snap the lens cover off by pressing 

down to release the two notches on 

the lens. (Fig. 19)

• Remove the light bulbs by pulling 

them out carefully.

• Replace with new bulbs by pushing 

them in.

• Replace the lens cover.

Fig. 19

To reduce the risk of electric 

shock, the power cord must be 

disconnected before removing the dust 

cup, dust cup filter,changing the filters or 

performing maintenance/trouble shooting 

checks.

To reduce the risk of electric 

shock, the power cord must be 

disconnected before removing the dust 

cup, dust cup filter,changing the filters or 

performing maintenance/trouble shooting 

checks.
The pre-motor filter is located 

underneath the dust cup. Please note 

that this filter is not a washable filter 

but should be cleaned frequently. To 

remove the pre-motor filter:

1. Remove the dust cup from the 

vacuum cleaner.

2. Make sure that you empty the dust 

cup before turning it upside down to 

remove the pre-motor filter.

3. Press inward on the two clips on 

the side of the filter and pull out to 

remove.

4. Clean the pre-motor filter by gently 

tapping over a trash container.

5. Replace the filter into the dust cup 

and push down until you hear it 

click into place.

9