Справочник Пользователя для American Standard 4454
4453 SERIES
4454 SERIES
4454 SERIES
ELITE
Installation
Instructions
M968202 REV.1.2
Certified to comply with ANSI A112.18.1M
1
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
CAUTION
Turn off hot and cold water
supplies before beginning.
supplies before beginning.
SINGLE CONTROL KITCHEN FAUCET
and HAND SPRAY
1
2
8
A
B
P U T T Y
S P O U T B A S E
S P O U T B A S E
S Q U A R E
S E A L R I N G
S E A L R I N G
8
S Q U A R E
S E A L R I N G
S E A L R I N G
4
S I N K O R
M O U N T I N G
S U R FA C E
2
3
4
5
6
7
9
3
0
1
2
3
4
5
6
Assemble RUBBER WASHER (5), BRASS WASHER (6), and threaded LOCKNUT (7) onto SHANK (4) from underside
of sink or mounting surface. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening
the screws slightly each time until all are snug to ensure even pressure.
of sink or mounting surface. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening
the screws slightly each time until all are snug to ensure even pressure.
(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON WITH PUTTY PLATE (1).
Insert supply HOSES (3) and SHANK (4) through hole of ESCUTCHEON WITH PUTTY PLATE (1) and mounting surface.
Make certain the SQUARE SEAL RING (2) is properly seated in recess of SPOUT BASE. Follow mounting instructions below
to secure faucet to mounting surface.
Make certain the SQUARE SEAL RING (2) is properly seated in recess of SPOUT BASE. Follow mounting instructions below
to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1). Remove ESCUTCHEON WITH PUTTY PLATE (1) and Insert supply HOSES (3) and
SHANK (4) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Make certain the SQUARE SEAL
RING (2) is properly seated in recess of SPOUT BASE. Do not use putty.
RING (2) is properly seated in recess of SPOUT BASE. Do not use putty.
CARE:
5
6
7
9
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
TOOLS REQUIRED
Plumbers' Putty or Caulking
Adjustable Wrench
Channel Locks
Regular Screwdriver
Phillips Screwdriver