Справочник Пользователя для ONKYO TX-NR5010
Controlling Other Components
En-99
The AV receiver’s remote controller can learn the
commands of other remote controllers. By transmitting, for
example, the Play command from your CD player’s remote
controller, the supplied remote controller can learn it and
then reproduce the exact same command when its
commands of other remote controllers. By transmitting, for
example, the Play command from your CD player’s remote
controller, the supplied remote controller can learn it and
then reproduce the exact same command when its
1 is
pressed in CD remote mode.
This is useful when some buttons don’t work as expected
though you entered the appropriate remote control code
(
This is useful when some buttons don’t work as expected
though you entered the appropriate remote control code
(
Note
• The following buttons cannot learn new commands:
8RECEIVER, ALL OFF, MY MOVIE, MY TV, MY MUSIC,
REMOTE MODE, MODE.
REMOTE MODE, MODE.
• The remote controller can learn approximately 70 to 90
commands, although this will be less if commands that use a lot
of memory are learned.
of memory are learned.
• Remote controller buttons such as Play, Stop, and Pause are
preprogrammed with commands for controlling Onkyo CD
players, cassette decks, and DVD players. However, they can
learn new commands, and you can restore the preprogrammed
commands at any time by resetting the remote controller
(
players, cassette decks, and DVD players. However, they can
learn new commands, and you can restore the preprogrammed
commands at any time by resetting the remote controller
(
• To overwrite a previously acquired command, repeat this
procedure.
• Depending on the remote controller used, some buttons may not
respond as expected, or the learning process itself may not be
possible.
possible.
• Only commands from infrared remote controllers can be
acquired.
• When the remote controller runs out of batteries, all commands
acquired will be lost and will have to be learned all over again.
Therefore, do not discard your other remote controllers.
Therefore, do not discard your other remote controllers.
■
Deleting Acquired Commands
1. While holding down the REMOTE MODE button for
the mode from which you want to delete a command,
press and hold down
8TV until the REMOTE MODE
button lights (about 3 seconds).
2. Press the REMOTE MODE button or the button from
which you want to delete the command.
The REMOTE MODE button flashes twice.
When you press the REMOTE MODE button, all
commands learned in that mode will be deleted.
The REMOTE MODE button flashes twice.
When you press the REMOTE MODE button, all
commands learned in that mode will be deleted.
Learning Commands
1
While holding down the
REMOTE MODE button
for the mode in which you want to use the
command, press and hold down
command, press and hold down
8RECEIVER
until the
REMOTE MODE button lights (about 3
seconds).
2
On the supplied remote controller, press the
button to which you want to assign the new
command.
button to which you want to assign the new
command.
3
Point the remote controllers at each other, within
about 4 inches (10 cm) apart, and then press and
hold the button whose command you want to
acquire until the
about 4 inches (10 cm) apart, and then press and
hold the button whose command you want to
acquire until the
REMOTE MODE button flashes.
8RECEIVER
REMOTE
MODE
If the command is learned successfully, the
REMOTE MODE button flashes twice.
REMOTE MODE button flashes twice.
4
To learn more commands, repeat steps 2 and 3.
Press any
REMOTE MODE button when you’ve
finished. The
REMOTE MODE button flashes
twice.
VO
LUME
UT
ING
PO
WER
SLEEP
DIMM
ER
SUR
MODE
VIDEO-1
VIDEO-2
TA
PE
DV
D
C D
C D
DV
D
TU
NER
TUNER
PHONO
INPUT SELECT
OR
DISC
CH SEL
PRESET
TEST
TO
N
E
MUL
TI-CH
INPUT
GR
OUP
Within about
4 inches (10 cm)
4 inches (10 cm)
Supplied remote
controller
controller