Справочник Пользователя для Marantz SR4500

Tune into the radio station you desire (Refer to
the 

” or 

section).

Press the 

button on the remote. “

“

(preset number) starts blinking on the display.

Enter the desired preset number by pressing
the 

buttons.

• When entering a single digit number (2 for

example), either input “02” or just input “2” and
wait for a few seconds.

Select the desired preset station by pressing
the   or   cursor

buttons on the front panel

Press the 

4

 or 

¢

 buttons to select the desired

preset station, or input your desired preset
channel with the 

buttons on the remote.

Press the 

on the remote.

“

” appears on the display and

then the preset station with the lowest preset
number is recalled first.

Preset stations are recalled in sequence (No.1

→

 No.2 

→

 etc.) for 5 seconds each.

No stored preset number will be skipped.

You can fast forward the preset stations by
pressing the 

¢

 continuously.

When the desired preset station is received,
cancel the preset scan operation by pressing
the 

 button or 

on the remote.

You can remove preset stations from the memory
using the following procedure.

Recall the preset number to be cleared with the
method described in “Recalling” a preset station.

Press the 

button on the front panel or

press the 

button on the remote.

The stored preset number blinks in the display
for 5 seconds. While blinking, press the

 button on the front panel or the remote.

“

” appears on the display to indicate

that the specified preset number has been
cleared.

• To clear all stored preset stations, press and hold

the  CLEAR and the ENTER buttons for two
seconds.

If you have stations memorized, and there is a gap
in the sequential order:
I.e. the stations are stored as follows

  1) 87.1 MHz
  2) 93.1 MHz
  3) 94.7 MHz
10) 105.9 MHz

(notice there is no stations programmed for pre
sets for 4-9), you can have pre set 10 become pre
set 5:
To sort the numbers, press and hold the 

 and

the 

cursor buttons.

“

” will appear on the display and

sorting will be done.

This function allows the name of each preset channel
to be entered using alphanumeric characters.
Before name inputting, you need to store preset
stations with the preset memory operation.

Recall the preset number to be inputted name
with the method described in “Recalling” a
preset station.

Press the 

button on the front panel or

press the 

button on the remote for

more than 3 seconds.

The left most column of the station name
indicator flashes, indicating the character
entry ready status.

When you press the   or 

cursor

buttons on

the front panel or the 

5

5

5

5

5 / 6

6

6

6

6

 buttons on the

remote, alphabetic and numeric characters will
be displayed in the following order:

→ B → C ... Z → 1 → 2 → 3 ..... 0 → –  → +

→ / → (Blank) → A

→

← DOWN

After selecting the first character to be entered,
press the 

or 

buttons, press the

button on the remote.

The entry in this column is fixed and the next
column starts to flash. Fill the next column the
same way.
To move back and forth between the characters,
press the

cursor

buttons or press 

4

 or 

¢

buttons on the remote.

• Unused columns should be filled by entering
blanks.

To save the name, press the 

button on

the front panel or remote for more than 2
seconds.

AAC

AAC

AAC

AAC

3

2

1

6

5

4

9

8

0

7

3

2

1

6

5

4

9

8

0

7

3

2

1

6

5

4

9

8

0

7

3

2

1

6

5

4

9

8

0

7

ENTER

Ten keypad

Press, press again, press again, etc.

1

A 

→ 

B 

→ 

C 

→ 

1 

→ 

A

2

D 

→ 

E 

→ 

F 

→ 

2 

→ 

D

3

G 

→ 

H 

→ 

I 

→ 

3 

→ 

G

4

J 

→ 

K 

→ 

L 

→ 

4 

→ 

J

5

M 

→ 

N 

→ 

O 

→ 

5 

→ 

M

6

P 

→ 

Q 

→ 

R 

→ 

6 

→ 

P

7

S 

→ 

T 

→ 

U 

→ 

7 

→ 

S

8

V 

→ 

W 

→ 

X 

→ 

8 

→ 

V

9

Y 

→ 

Z 

→ 

space 

→ 

9 

→ 

Y

0

– 

→ 

+ 

→ 

/ 

→ 

0

SR4500N DFU_01_ENG 2_2

04.5.14, 4:27 PM

Page 31

Adobe PageMaker 6.5J/PPC