Справочник Пользователя для Liebherr 211111 7085270 - 00

2.1

Installing the appliance.............................................

2

2.2

Changing over door hinges......................................

3

2.3

Built-in......................................................................

4

2.4

Connecting the appliance.........................................

8

The manufacturer works constantly on the further development

of all the types and models. Therefore please understand that

we  have  to  reserve  the  right  to  make  design,  equipment  and

technical modifications.
To get to know all the benefits of your new appliance, please

read the information contained in these instructions carefully.
The  instructions  apply  to  several  models.  Differences  may

occur. Text relating only to specific appliances is marked with

an asterisk (*).
Instructions for action are marked with a  , the results of

DANGER

identifies a situation involving direct

danger which, if not obviated, may

result in death or severe bodily

injury.

WARNING

identifies a dangerous situation

which, if not obviated, may result in

death or severe bodily injury.

CAUTION

identifies a dangerous situation

which, if not obviated, may result in

minor or medium bodily injury.

NOTICE

identifies a dangerous situation

which, if not obviated, may result in

damage to property.

Note

identifies useful information and tips.

It is important that the procedures and directions given in these

instructions  are  complied  with  in  order  that  the  appliance  is

correctly installed and works properly. Read and grasp all the

information  in  these  instructions  before  the  appliance  is

installed.

Risk of fire due to short circuit!

If  the  mains  cable/connector  of  the  appliance  or  of  another

appliance  touch  the  rear  of  the  appliance,  the  mains  cable/

connector  may  be  damaged  by  the  appliance  vibrations,

leading to a short circuit.

u

Stand the appliance so that it is not touched by connectors

or main cables.

u

Do not plug the appliance or any others into sockets located

near the rear of the appliance.

Fire hazard due to dampness!

If  live  parts  or  the  mains  lead  become  damp  this  may  cause

short circuits.

u

The appliance is designed for use in enclosed areas. Do not

operate  the  appliance  outdoors  or  in  areas  where  it  is

exposed to splash water or damp conditions.

u

Only use the appliance when it is installed.

Fire hazard due to refrigerant!

The  refrigerant  R  600a  is  environmentally  friendly  but  flam-

mable. Escaping refrigerant may ignite.

u

Do not damage the piping of the refrigeration circuit.

Fire hazard and danger of damage!

u

Do  not  place  appliances  emitting  heat  e.g.  microwaves,

toasters etc. on the appliance!

Blocked ventilation openings pose a risk of fire and damage!

u

Always keep the ventilation openings clear. Always ensure

that the appliance is properly ventilated!

q

In  the  event  that  the  appliance  is  damaged,  contact  the

supplier immediately before connecting to the mains.

q

The floor at the site must be flat and level.

q

Do not install the appliance in a location where it is exposed

to  direct  radiation  of  the  sun,  next  to  a  cooker,  heater  and

similar.

q

The appliance is suitable for integrated, under-worktop use.

q

Ventilation is effected by way of the plinth.

q

Do not install the appliance without assistance.

q

Standard EN 378 specifies that the room in which you install

your  appliance  must  have  a  volume  of  1  m

2

  per  8  g  of  R

600a refrigerant used in the appliance. If the room in which

the  appliance  is  installed  is  too  small,  a  flammable  gas-air

mixture may form in the event of a leakage in the refrigera-

tion circuit. The quantity of refrigerant used in your appliance

is indicated on the type plate on the inside of the appliance.

u

Detach the connecting cable from the rear of the appliance,

removing the cable holder at the same time because other-

wise there will be vibratory noise!

After installation:

u

Remove the protective film from the decorative trims.*

u

Remove all transit supports.

u

Unscrew  the  red  transport

lock.  Close  the  vacated

retaining  hole  using  the

stopper (60).

u

Dispose of packaging material.

For Side-by-Side installation, freezer and refrigerator side by

side:

u

Always install the freezer on the right of the refrigerator, as

seen from the front.

w

No condensate forms between the appliances thanks to the

side wall heating system foamed in on the left.

u

Clean the appliance .