Справочник Пользователя для ResMed 2011-09
29
Technical specifications
En
glish
Voltage dips,
short
interruptions
and voltage
variations on
power supply
input lines
IEC 61000-4-11
short
interruptions
and voltage
variations on
power supply
input lines
IEC 61000-4-11
<5% Ut (>95% dip in
Ut) for 0.5 cycle
Ut) for 0.5 cycle
40% Ut (60% dip in
Ut) for 5 cycles
Ut) for 5 cycles
70% Ut (30% dip in
Ut) for 25 cycles
Ut) for 25 cycles
<5% Ut (>95% dip in
Ut) for 5 sec
Ut) for 5 sec
< 12 V (>95% dip in
240V) for 0.5 cycle
240V) for 0.5 cycle
96 V (60% dip in
240 V) for 5 cycles
240 V) for 5 cycles
168 V (30% dip in
240 V) for 25 cycles
240 V) for 25 cycles
<12 V (>95% dip in
240 V) for 5 sec
240 V) for 5 sec
Mains power quality should be that of a typical
commercial or hospital environment.
If the user of the device requires continued
operation during power mains interruptions, it is
recommended that the device be powered from
an uninterruptible power source.
commercial or hospital environment.
If the user of the device requires continued
operation during power mains interruptions, it is
recommended that the device be powered from
an uninterruptible power source.
Power
frequency
frequency
(50/60 Hz)
magnetic field
IEC 61000-4-8
magnetic field
IEC 61000-4-8
3 A/m
3 A/m
Power frequency magnetic fields should be at
levels characteristic of a typical location in a
typical commercial or hospital environment.
levels characteristic of a typical location in a
typical commercial or hospital environment.
Portable and mobile RF communications
equipment should be used no closer to any part
of the device, including cables, than the
recommended separation distance calculated
from the equation applicable to the frequency of
the transmitter.
Recommended separation distance:
equipment should be used no closer to any part
of the device, including cables, than the
recommended separation distance calculated
from the equation applicable to the frequency of
the transmitter.
Recommended separation distance:
Conducted RF
IEC 61000-4-6
3 Vrms
150 kHz to 80 MHz
3 Vrms
d = 1.17
√P
Radiated RF
IEC 61000-4-3
10 V/m
80 MHz to 2.5 GHz
80 MHz to 2.5 GHz
3 V/m
d = 0.35
√P 80 MHz to 800 MHz
d = 0.70
√P 800 MHz to 2.5 GHz
where P is the maximum output power rating of
the transmitter in watts (W) according to the
transmitter manufacturer and d is the
recommended separation distance in metres (m).
Field strengths from fixed RF transmitters, as
determined by an electromagnetic site survey,
the transmitter in watts (W) according to the
transmitter manufacturer and d is the
recommended separation distance in metres (m).
Field strengths from fixed RF transmitters, as
determined by an electromagnetic site survey,
a
should be less than the compliance level in each
frequency range.
frequency range.
b
Interference may occur in the vicinity of
equipment marked with the following symbol:
equipment marked with the following symbol:
NOTE 1: Ut is the AC mains voltage prior to application of the test level.
NOTE 2: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 3: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection
from structures, objects and people.
NOTE 2: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 3: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection
from structures, objects and people.
a
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios,
amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the
electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the
measured field strength in the location in which the device is used exceeds the applicable RF compliance level above, the device
should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary,
such as reorienting or relocating the device.
electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the
measured field strength in the location in which the device is used exceeds the applicable RF compliance level above, the device
should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary,
such as reorienting or relocating the device.
b
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 10 V/m.
Recommended separation distances between portable and mobile RF communications equipment and the
device
device
The device is intended for use in an environment in which radiated RF disturbances are controlled. The customer or
the user of the device can help prevent electromagnetic interference by maintaining a minimum distance between
portable and mobile RF communications equipment (transmitters) and the device as recommended below, according
to the maximum output power of the communications equipment.
the user of the device can help prevent electromagnetic interference by maintaining a minimum distance between
portable and mobile RF communications equipment (transmitters) and the device as recommended below, according
to the maximum output power of the communications equipment.
Separation distance according to frequency of transmitter (m)
Rated maximum output
power of transmitter (W)
power of transmitter (W)
150 kHz to 80 MHz
d = 1.17
d = 1.17
√P
80 MHz to 800 MHz
d = 0.35
d = 0.35
√P
800 MHz to 2.5 GHz
d = 0.7
d = 0.7
√P
0.01
0.17
0.04
0.07
0.1
0.37
0.11
0.22
1
1.17
0.35
0.7