Справочник Пользователя для Cisco 2600 Enterprise Plus Feature Pack CD26-AP-12.0.7=
Модели
CD26-AP-12.0.7=
22 Release Notes for Cisco IOS Release 12.0(7)XK1 Feature Packs for Cisco 2600 Series Routers
Installation Notes
If the file is still not found, create a temporary directory entitled “C:\temp,” and copy the
CiscoPro upgrade file into the directory. Select the C:\temp directory as the root directory.
CiscoPro upgrade file into the directory. Select the C:\temp directory as the root directory.
Step 15
When asked whether you want to erase the existing image in the router Flash memory
before copying the new one, enter yes:
before copying the new one, enter yes:
Erase flash device before writing? [confirm] yes
The entire copying process takes several minutes and differs from network to network.
The exclamation point (!) indicates that the copy process is taking place. Each
exclamation point indicates that ten packets have been transferred successfully. If you see
three or more periods (...), the transfer might fail. If the transfer fails, use the ping
command to check IP connectivity between the router and TFTP server.
The exclamation point (!) indicates that the copy process is taking place. Each
exclamation point indicates that ten packets have been transferred successfully. If you see
three or more periods (...), the transfer might fail. If the transfer fails, use the ping
command to check IP connectivity between the router and TFTP server.
Step 16
Enter the reload command to reload the router:
Router(boot)# reload
Do not save the configuration.
After reload is complete, your CiscoPro router has been upgraded to a Cisco Enterprise
router. Because the original Cisco IOS image that resided in Flash memory was erased
during the upgrade process, the router is now running in bootstrap mode.
router. Because the original Cisco IOS image that resided in Flash memory was erased
during the upgrade process, the router is now running in bootstrap mode.
Step 17
If the password prompt appears, enter the password.
Password: <password>
Step 18
At the router prompt, enter enable and then the password:
Router(boot)# enable
Password: <password>
Step 19
At the router prompt, enter the following command to copy the new software image from
the PC CD-ROM drive to the router:
the PC CD-ROM drive to the router:
Router(boot)(config)# copy tftp flash
In the next series of steps, you download the Cisco IOS Release 12.0(7)XK1 images that
you want installed on your router.
you want installed on your router.
Step 20
When prompted, enter the IP address of your PC, as in the following example:
Address or name of remote host [255.255.255.255]? 172.11.1.1
This is the IP address of your local PC, not that of the router.
Step 21
When prompted, enter the filename of the Cisco IOS Release 12.0(7)XK1 image to be
copied to the router, as in the following example:
copied to the router, as in the following example:
Source file name? aaa1308.bin
This example specifies the DOS image name of the IP feature set for Cisco 2600 series
routers (as shown in Table 4 in the “Feature Pack Overview” section on page 7).
routers (as shown in Table 4 in the “Feature Pack Overview” section on page 7).
Step 22
In response to the prompt, enter the destination UNIX image filename, and press Enter.
This is the name of the image file on the router, not the full pathname of the image on the
CD-ROM attached to the PC. Refer to Table 4 in the “Feature Pack Overview” section on
page 7 for the UNIX image filename.
CD-ROM attached to the PC. Refer to Table 4 in the “Feature Pack Overview” section on
page 7 for the UNIX image filename.
Destination file name [aaa01308.bin]? c2600-i-mz.120-7.XK1
During the transfer process, the software displays messages indicating that it has accessed
the file you have specified and is loading it.
the file you have specified and is loading it.