Руководство По Обслуживанию для Cisco Cisco TelePresence MX700
D15331.02 MX700 and MX800 Administrator Guide CE8.1, APRIL 2016.
www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
153
Cisco TelePresence MX700 and MX800
Administrator Guide
Video Output Connector [2] CEC Mode
This setting only applies to MX800 Single.
This video output (HDMI) supports Consumer Electronics Control (CEC). When this setting
This video output (HDMI) supports Consumer Electronics Control (CEC). When this setting
is On (default is Off), the system will use CEC to set the monitor in standby when the system
itself enters standby. Likewise the system will wake up the monitor when the system itself
wakes up from standby. For this to happen, the monitor that is connected to the output must
be CEC compatible and CEC must be configured on the monitor.
Note that the different manufacturers uses different marketing names for CEC, for example
Note that the different manufacturers uses different marketing names for CEC, for example
Anynet+ (Samsung); Aquos Link (Sharp); BRAVIA Sync (Sony); HDMI-CEC (Hitachi); Kuro
Link (Pioneer); CE-Link and Regza Link (Toshiba); RIHD (Onkyo); HDAVI Control, EZ-Sync,
VIERA Link (Panasonic); EasyLink (Philips); and NetCommand for HDMI (Mitsubishi).
Requires user role: ADMIN
Default value: Off
Default value: Off
Value space: Off/On
Off: Disable CEC control
On: Enable CEC control
On: Enable CEC control
Video Output Connector [1..3] Location HorizontalOffset
HorizontalOffset and VerticalOffset settings are associated with each video output. These
settings are used to signal the relative position of the displays that are connected to these
outputs.
HorizontalOffset = 0 and VerticalOffset = 0 indicates that the display is positioned in center,
HorizontalOffset = 0 and VerticalOffset = 0 indicates that the display is positioned in center,
both horizontally and vertically. A negative horizontal offset indicates that the monitor is
left of center, and a positive horizontal offset indicates that the monitor is right of center.
A negative vertical offset indicates that the monitor is below center, and a positive vertical
offset indicates that the monitor is above center. The magnitude of the offset indicates how
far the display is from center (relative to other displays).
Example: You have three displays side by side, with the left and right displays at equal
Example: You have three displays side by side, with the left and right displays at equal
distance from center. Then the following settings will apply: HorizontalOffset = 0 for the
center display, HorizontalOffset = -1 for the left display, and HorizontalOffset = 1 for the
right display.
Example: You have two displays, one in center and one below. Then the following settings
Example: You have two displays, one in center and one below. Then the following settings
will apply: VerticalOffset = 0 for the center display, Vertical Offset = -1 for the lower display.
The default values for the different outputs are:
Video Output Connector [1] Location: HorizontalOffset = -1, VerticalOffset = 0
Video Output Connector [2] Location: HorizontalOffset = 0, VerticalOffset = 0
Video Output Connector [3] Location: HorizontalOffset = 1, VerticalOffset = 0
The default values for the different outputs are:
Video Output Connector [1] Location: HorizontalOffset = -1, VerticalOffset = 0
Video Output Connector [2] Location: HorizontalOffset = 0, VerticalOffset = 0
Video Output Connector [3] Location: HorizontalOffset = 1, VerticalOffset = 0
Requires user role: ADMIN
Default value: Connector [1]: -1 Connector [2]: 0 Connector [3]: 1
Default value: Connector [1]: -1 Connector [2]: 0 Connector [3]: 1
Value space: Integer (-100..100)
Range: The value must be between -100 and 100.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices
System settings