Справочник Пользователя для Samsung RS727CQRBSLA
setting up _11
01 SETTING
UP
If you have to repair or disassemble the water line,
cut off 6.5mm of the plastic tubing to make sure you
get a snug, leak-free connection.
cut off 6.5mm of the plastic tubing to make sure you
get a snug, leak-free connection.
Before being used, the leakage in these
places should be examined.
places should be examined.
• Samsung Warranty does not cover WATER LINE
INSTALLATION.
• It’ll be done at customer’s charge unless the retail
price includes installation cost.
• Please contact Plumber or Authorized Installer for
the installation if needed.
• If Water leakage occurs due to improper
installation, Please contact installer.
1. Slip the
compression nut
(A) through the
supplied plastic
tubing (A).
(A) through the
supplied plastic
tubing (A).
2. Tighten the
compression nut
(A) onto the 1/4”
compression fitting.
(A) onto the 1/4”
compression fitting.
- If you are using
copper tubing, slip
the compression
nut (B) (not included) and ferrule (not included) on
copper tubing (not included) as shown.
the compression
nut (B) (not included) and ferrule (not included) on
copper tubing (not included) as shown.
- If you are using plastic tubing (B), insert the
molded end(Bulb) of the plastic tubing (B) into
the compression fitting.
the compression fitting.
Do not use without the molded end(Bulb) of
the plastic tubing (B).
the plastic tubing (B).
3. Tighten the compression nut (B) onto the
compression fitting. Do not over-tighten the
compression nut (B).
compression nut (B).
4. Turn water on and check for any leakage.
Only connect the water line to a drinkable
water source.
water source.
If you have to repair or disassemble the water
line, cut off 1/4“ of the plastic tubing to make
sure you get a snug, leak-free connection.
line, cut off 1/4“ of the plastic tubing to make
sure you get a snug, leak-free connection.
Check the accessory list below.
Water line fixer and
screws
Pipe connector
Water line
Clip
Connecting to the water supply line
1. First, shut off the main water supply line.
2. Locate the nearest cold, drinking water line.
3. Follow the Water Line Installation Instructions in
2. Locate the nearest cold, drinking water line.
3. Follow the Water Line Installation Instructions in
the installation kit.
4. After connecting the water supply to the water
filter, turn your main water supply back on and
Dispense about 3L to clear and prime the water
filter.
Dispense about 3L to clear and prime the water
filter.
Connecting the water line to the
refrigerator
refrigerator
1. Remove the cap from water line on the unit and
insert compression nut to the water line on the
unit after disassembling from provided water line.
unit after disassembling from provided water line.
2. Connect both water line from the unit and water
line in the kit.
3. Tighten the compression nut onto the
compression fitting. Be careful no gap between
two items.
two items.
4. Turn water on and check for any leakage.
Only connect the water line to a drinkable
water source.
water source.
CAUTION
The water line must be connected to
the cold water pipe.
If it is connected to the hot water pipe,
it may cause the purifier to malfunction.
the cold water pipe.
If it is connected to the hot water pipe,
it may cause the purifier to malfunction.
Close Main
Close Main
Water pipe
Water pipe
Water pipe
Close Main
Close Main
Water pipe
Water pipe
Water pipe
No gap
No gap
Remove
Remove
cap
cap
Water Line
Water Line
from unit
from unit
from unit
Water Line
Water Line
from Kit
from Kit
from Kit
No gap
No gap
Loosen a
Loosen a
No Leak
No Leak
CAUTION
CAUTION