Справочник Пользователя для Panasonic CQ-C1200U
POWER
CLOCK
CQ-C1200U
DI
SP
SQ
MUTE
7
8
9
10
11
12
SCAN
1
2
3
4
6
APM
BA
N
D
SRC
5
VOL
UME /
PUSH SE
L
REP
TUNE
TRACK
D
•
M
POWER
CLOCK
CQ-C1200U
DI
SP
SQ
MUTE
7
8
9
10
11
12
SCAN
1
2
3
4
6
APM
BA
N
D
SRC
5
VOL
UME
/ PUSH SE
L
REP
TUNE
TRACK
D
•
M
1
E
N
N
G
L
I
S
H
H
13
CQ-C1200U/C1120U/C1110U/C1100U
1
E
N
N
G
L
I
S
H
H
2
12
CQ-C1200U/C1120U/C1110U/C1100U
Hours
w
Press and hold [DISP] (clock) for more than 2
seconds.
seconds.
e
Press [k TUNE] or [l TUNE].
Minutes
r
Press [DISP] (clock).
t
Press [k TUNE] or [l TUNE].
y
Press [DISP] (clock).
Note: Press and hold [k TUNE] or [l TUNE] to
change numbers rapidly.
change numbers rapidly.
Audio Mode
(Bass/Treble/Balance/Fader/Sub Woofer)
(Bass/Treble/Balance/Fader/Sub Woofer)
Regular mode
Volume
Bass
Treble
Balance
Sub Woofer
Fader
Note: If no operation takes place for more than 5 sec-
onds in audio mode (2 seconds in volume mode), the
display returns to the regular mode.
onds in audio mode (2 seconds in volume mode), the
display returns to the regular mode.
Bass:
Adjustable range: –12 to +12 (by 2 dB step)
Treble:
Adjustable range: –12 to +12 (by 2 dB step)
Balance:
R (right speaker) or L (left speaker)
Fader:
F (front speaker) or R (rear speaker)
Push [SEL] to select the audio mode.
q
Clock Setting
The 12-hour system is used for the clock.
(Hours blink.)
(Hours set.)
(Minutes blink.)
(Minutes set.)
(End.)
Initial Time
q
Press [DISP] (clock).
"AdJ" is displayed when the clock is not
adjusted.
adjusted.
Time Reset
Press and hold [DISP] (clock) for more than
2 seconds to activate the time setting mode to
reset the time. Then, repeat steps e to y.
2 seconds to activate the time setting mode to
reset the time. Then, repeat steps e to y.
[DISP] (clock)
[k TUNE], [l TUNE] (Hours, minutes)
Adjustable range: 1 to 15 (by 1 step) Balance center
Adjustable range: 1 to 15 (by 1 step)
Fader center
(Only for CQ-C1200U)
Sub Woofer:
Adjustable range (level): MUTE (0) to 7
(Only for CQ-C1200U)
Push
Turn [VOLUME] clockwise or counterclockwise
to change each level.
to change each level.
w
default: 0 dB
default: 0 dB
(default)
(default)
default: 4
D
IS
P
SQ
MUTE
SRC
Power and Sound Controls
Mute
Press [MUTE] to mute the sound completely.
lights
Press [MUTE] again to cancel.
Volume
Turn the knob clockwise to increase volume,
and counterclockwise to decrease volume.
and counterclockwise to decrease volume.
Volume level (0 to 40)
(default: 18)
SQ (Sound Quality)
SQ is a function that can call up various sound types at
the touch of button in accordance with your listening
music type.
the touch of button in accordance with your listening
music type.
Press [SQ] to select a sound type as follows:
(default)
SQ -- (default)
flat frequency response:
does not emphasize.
does not emphasize.
SQ - 1 (ROCK)
speedy and heavy sound:
exaggerates bass and treble.
exaggerates bass and treble.
SQ - 2 (POP)
wide-ranged and deep sound:
slightly emphasizes bass and treble.
slightly emphasizes bass and treble.
SQ - 3 (VOCAL)
clear sound:
emphasizes middle tone and
slightly emphasizes treble.
emphasizes middle tone and
slightly emphasizes treble.
Power
Turn the key in the ignition until
the accessory indicator lights.
Power on: Press [SRC] (POWER).
Power off: Press [SRC](POWER)
the accessory indicator lights.
Power on: Press [SRC] (POWER).
Power off: Press [SRC](POWER)
again and hold.
ACC
ON
MUTE
ST
Display Change
Press [DISP] (display) to switch to the clock display.
Note: "AdJ" is displayed when the clock is not adjusted.
(
(
➡
page 13)
When the power is off:
No display
Clock display
Remote control sensor (
➡
page 18)*
(only for CQ-C1200U/C1120U/C1110U)
Up
Down
SQ indicator
Notes:
• If no operation takes place for more than 2 seconds in the SQ mode, the display returns to the regular mode.
•
• If no operation takes place for more than 2 seconds in the SQ mode, the display returns to the regular mode.
•
Settings of SQ, bass/treble are influenced one another. If the influence mentioned above causes distortion to audio signal,
readjust bass/treble or volume (
➡
page 13)
.
• CQ-C1100U has no remote control function.*