Справочник Пользователя для Panasonic dmr-e100heb

∫ Recording

[HDD] [RAM] [DVD-R]

This is a simple way to make timer recordings when you are in a 
hurry or before you go to bed. You can set the time up to 4 hours in 
advance.

¥, REC] on the main unit to select 

The time increases as illustrated by each press of the button.
The counter decreases in 1-minute units after you set a time. You 
can change the time again with the same operation.
When the time you set is reached, recording stops and the unit 
switches to standby.

Unit’s Display
(Counter) 

# 30 # 60 # 90

^ 240 ! 180 ! 120 !}

ªTo cancel

During recording, press [

¥, REC] until the counter appears.

≥Recording continues.

ªTo show the time remaining until 

≥It is displayed in the unit of minute.

For your reference
≥This does not work during timer recordings or flexible recording.
≥Recording stops and the set time is cleared if you press 

[

∫, STOP].

≥The set time is cleared if you change the recording mode or 

channel while recording is paused.

This function allows you to immediately start recording the same 
programme that you are viewing on the TV.
The programme position selected on the unit automatically 
changes to that of the TV programme that you are viewing on the 
TV.
Conditions for the Direct TV Recording function:
≥Your TV must be equipped with the [Q Link] function.
≥The unit must be connected to the TV via a fully-wired 21-pin 

Scart cable.

[1] Press [HDD] or [DVD] to select the 

(page 19)

[2]

When DVD mode was selected above: 

(page 19)

[3] Press [DIRECT TV REC].

≥Recording of the TV programme that you are viewing on the 

TV starts.

[4] Press [

∫, STOP] to stop recording.

Note
≥When you stop recording, the unit automatically switches back to 

the previously selected programme position.

[HDD] [RAM] [DVD-R]
If an external equipment (e.g., a satellite receiver) with a timer 
function is connected to the AV2 socket of this unit by a 21-pin 
cable, it is possible to control the recording of the unit with the 
equipment. For the connection to the external equipment, see 
page 57.
Preparation
≥Make sure that “AV2 Connection” is set to “Ext Link 1” or 

“Ext Link 2”. (page 61)

≥Timer programming has to be done on the external equipment 

and switch to the timer recording standby mode. Refer to the 
equipment’s operating instructions.

1) Press [EXT LINK] on the unit to switch the unit over to the timer 

recording standby mode.
≥As long as a video 

picture is being 
transmitted by the 
Satellite or Digital 
Receiver, the unit 
will record it.
The notice is 
displayed on the 
TV screen.
(Only when [Ext Link 2] is selected)
To delete it, press [ENTER].

2) To cancel the external control, turn off the timer recording 

standby mode of the unit by pressing [EXT LINK] again.

For your reference
≥To switch TV automatically to the picture from the unit in 

playback mode, connect the AV1 socket of this unit to the TV by 
a 21-pin cable.

≥This function does not work with some equipment. Refer to the 

equipment’s operating instructions.

≥The beginning of recordings may not be recorded correctly in 

some cases.

≥When “AV2 Connection” is set to “Ext Link 2”, this function does 

not work if the input signal is NTSC system.

≥The play picture or menu picture is not output from AV2 socket 

during Linked timer recording standby mode.

DVD

TV

INPUT SELECT

VIDEO Plus+ DIRECT TV REC

AV

CH

DVD

TV

SKIP

DIRECT NAVIGATOR

PLAY LIST

TOP MENU

ENTER

MENU

FUNCTIONS

RETURN

STOP

PAUSE

PLAY/x1.3

SLOW/SEARCH

FRAME

MANUAL SKIP TIME SLIP

ERASE

REC

PROG/CHECK TIMER

DUBBING REC MODE

STATUS

MARKER

AUDIO

DISPLAY

POSITION

MEMORY

A

B

C

D

3

, 4, 2, 1

∫

HDD

DVD

REC/OTR  30

ARD

L R

DVD-RAM

DVD(B).book  28 ページ  ２００３年８月５日 火曜日 午後３時３０分