Справочник Пользователя для JVC dr-m10s
Masterpage:Right-No-Heading
EN
57
Filename [DR-M10SE_08Recording.fm]
Page 57
February 12, 2004 5:15 pm
F
Enter the recording stop time.
Press w e to select “STOP”, then press rt repeatedly to
set the desired stop time.
set the desired stop time.
● Each press of rt advances/goes back the stop time in 1-min.
increments.
● To advance/go back the stop time in 30-min. increments, press
and hold rt.
G
Enter the channel position.
Press w e to select “TV PROG”, then press rt
repeatedly to select the desired channel.
repeatedly to select the desired channel.
H
Set the other recording options as required.
Refer to step
I
Access the confirmation screen.
Press ENTER.
J
Complete timer programming.
Press ENTER.
K
Engage the unit’s timer mode.
Press # (TIMER). The unit turns off automatically and
“#” appears on the front display panel.
“#” appears on the front display panel.
● To disengage the timer mode, press # (TIMER) again.
NOTES:
● The beginning of a programme may not be recorded. Also, if
the 1st programme’s recording stop time and the 2nd
programme’s recording start time is the same, the ending of the
1st programme may not be recorded.
programme’s recording start time is the same, the ending of the
1st programme may not be recorded.
● If the copy limited programme is received during timer-
recording, the unit enters Record Pause mode. Recording starts
again if it is switched to a recordable broadcast during the
time you programmed.
again if it is switched to a recordable broadcast during the
time you programmed.
Satellite Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programming:
A Perform “Satellite Receiver Control Setting” on page 26.
B Perform “Manual Timer Programming”. In step G, press
Programming:
A Perform “Satellite Receiver Control Setting” on page 26.
B Perform “Manual Timer Programming”. In step G, press
AUX to change “TV PROG” to “SAT”. Then press rt to
enter the channel position for the satellite broadcast. In
step
enter the channel position for the satellite broadcast. In
step
H, you cannot set “VPS/PDC” to “ON”.
C Leave the satellite receiver’s power on.
VPS/PDC Recording
Now available from some TV stations, PDC (Programme
Delivery Control) and VPS (Video Programme System) are
services designed to assure safe, accurate timer recording.
With this system, special code signals are transmitted
together with the audio/video signals. These code signals
control your video unit and have precedence over the
advertised times you may have preset into the timer. This
means that your unit will start and stop recording when the
preset TV programmes actually start and end — even if the
broadcast time of a preset TV programme is changed.
Delivery Control) and VPS (Video Programme System) are
services designed to assure safe, accurate timer recording.
With this system, special code signals are transmitted
together with the audio/video signals. These code signals
control your video unit and have precedence over the
advertised times you may have preset into the timer. This
means that your unit will start and stop recording when the
preset TV programmes actually start and end — even if the
broadcast time of a preset TV programme is changed.
NOTES:
● When you use Manual Timer Programming, set the start
time (VPS or PDC time) exactly as advertised in the TV
listing. A different time than advertised will result in no
recording.
listing. A different time than advertised will result in no
recording.
● VPS/PDC recording is also possible when a satellite
receiver or a cable system is connected to L-2 IN/
DECODER connector on your unit.
DECODER connector on your unit.
● VPS/PDC recording is also possible via the L-1 IN/OUT
connector.
How to check if the station being received transmits a
VPS/PDC signal
VPS/PDC signal
A Hold down DISPLAY for about 5 seconds. “VPS/PDC”
appears blinking on the front display panel. If a VPS/PDC
signal is detected from the station, “VPS/PDC” will stop
blinking. If no VPS/PDC signal is detected from the
station, “VPS/PDC” will blink at a slower rate.
signal is detected from the station, “VPS/PDC” will stop
blinking. If no VPS/PDC signal is detected from the
station, “VPS/PDC” will blink at a slower rate.
B Press DISPLAY again to return to normal display.
DR-M10SE_01.book Page 57 Thursday, February 12, 2004 9:08 PM