Справочник Пользователя для Pelco C579M

C1510M-A (2/03)

SECTION 2

Programming from the 

 only.

The programming setup for this configuration is illustrated in Figure
2-2. Note that all monitor-outs on the 

 are used as tie lines

that go to the 

.

With this configuration, the minimum hardware requirements before
programming can begin are as follows:

a.

Monitor-outs from the 

 (tie lines) are connected to available

video inputs on the matrix bay on the 

  (see the

“NOTE” about tie line connection in 

, 

2.0 Video Tie

Lines

).

b.

The COM line between the two pieces of equipment is in place.

c.

You have a list of camera attributes for those cameras/receivers
that are or will be attached to the 

. It is not necessary for

them to be physically attached to the 

 for programming to

be possible. When attached, however, the programmed attribute
for that input must correspond to the equipment connected.

d.

The 

 is powered ON (plugged in).

e.

The items listed in step 2b of the previous programming con-
figuration (the Comms, the Cameras and the Link Cameras con-
figuration files) are programmed and integrated into the 9760
System.

Once the 9760 System is initialized using the configuration files just
mentioned, you can proceed to program the 

.

f.

Repeat steps 2c, 2d, and 2e of Programming Configuration II.

    No operator is required on the 

  of the

system. All programming is done from the 

. The number

of tie lines available for operator access from the 

 of the

configuration is at a maximum.

  You only use the 

 for its alarm reporting ca-

pabilities back to the head-end. Local satellite 

 operations

are not possible.

Programming Diagram Two

Here we want to make some comments and put forth some suggestion about how you might use variations to the previous programming
configurations based upon how the 9760-SAT interface works. The following observations and general statements can be made:

1.

As long as there is one tie line and a Com line in place between the 

 and the 9760 System, all attributes of 

 configuration can be

programmed from the 

 via a preset call.

2.

Normally, you should not initialize a keyboard (

) using a monitor-out line that has been configured as a tie line. However, under

certain circumstances, you might want to do this. The result of this action (from the 

 point of view) is that a monitor on the 

 is used as a “substitute” local monitor for programming the 

. The programming itself, however, is done from the 

Doing this allows one to program from the 

 without using a preset call. Unfortunately, this can only be done if the operators on

both sides of the configuration can physically talk to each other during the programming process because the 

 must initiate and

exit the programming mode based on queues received from the 

.

3.

Each side of the 9760-SAT configuration can be programmed independent of the other. Neither has to be physically connected to the other
for programming to be done as long as the programmed parameters of each match the physical parameters of the final equipment configu-
ration. System 9760-SAT related files (Comms, Link Cameras and Cameras) are programmed only from the 

 of the configura-

tion. 

 menu software, however, can be programmed from either side of a configuration.

 Use the same configuration and program the 

 from the 

.

(d)

Proceed to the DEF (define) sub-menu. (You may need to press
the ESC key first, then press the DEF key). If this is the first time
accessing that menu, enter the PIN (default 

).See Figures

3-20 and 3-22 in 

, 

3.2 9760 System-SAT Alarm Re-

sponse.

(e)

Next, enter 

 into the 9760 keypad and then press the PRST

key (while still within the DEF menu). The main programming
menu of the 

 appears on the monitor in front of you.

  You can program from the system side without losing

the benefits of local 

 operation; therefore, someone not able to

program the 

 could, at least, operate 

 functions.

    Before initiating programming from the 

, you must ensure that no one, other than the programmer, is

calling up any link cameras or otherwise utilizing any tie lines con-
nected to the 

. It’s possible for the 

 programming menu to

inadvertently appear on their monitor instead of the programmer’s
monitor.

 A link camera must be called as part of the programming process here. It is not necessary that the camera called be connected to the 

.

The same equipment diagram used above is applicable here. Here, a
conscious choice is made to the program from the 

 rather

than the 

. If you want, programming chores can be split

between either side, although that is not recommended.

(a)

Ensure no one else on the 

 is using an 

 tie line.

(b)

Ensure that the following items are in place:

1.

The Link camera you plan to call** should already be in-
cluded in the programmed Link Cameras file of the System
Manager (see 

, 

3.3 Link Cameras File)

.

2.

The tie lines coming from the 

 to the MXB on the 

 should be identified and programmed into the Sys-

tem Manager’s Cameras file (see 

, 

3.2 Cam-

eras File)

.

(c)

From the 9760 KBD, call up any link camera programmed in the
Link Camera file (see 

, 

2.1 Selecting Link [Satallite]

Cameras)

.