Справочник Пользователя для Mitsubishi Electronics colorview xd480u

 

EN - 13

1.  Tilt up the project to the appropriate angle. 
2.  Press the foot adjustment buttons next to the adjust-

ment feet (rear), and the adjustment feet will come 
out. 

3.  Release the buttons to lock the adjustment feet (rear) 

to that position.

4.  Rotate the adjustment feet (rear) for fi ne adjustment.

After using the projector:
5.  Put the adjustment feet (rear) back into the projector 

by pressing the foot adjustment buttons.

Important: 
•  If necessary, rotate the adjustment feet (front) for fi ne 

adjustment. 

•  Install the screen on a fl at wall at 90 degrees to the 

fl oor. 

•  Slanting the projector more than ±10˚ (right and left) 

or ±15˚ (front and rear) may cause trouble or explo-
sion of the lamp. You can tilt the projector up to 7 
degrees using the adjustment feet only.  

•  Images may not be projected in a shape of a regular 

rectangle or with its aspect ratio 4:3, depending on 
the installation conditions of the projector and the 
screen. 

•  To correct vertical and horizontal keystone distortion, 

press the KEYSTONE button on the projector or the 
remote control to display KEYSTONE, and adjust the 
image by pressing the 

, , ,  button (or VOL-

UME +, - button on the remote control). 

1.  Attach the provided power cord to the projector.
2.  Plug the power cord in the wall outlet. 
3.  Remove the lens cap.

Warning:
•  Do not look into the lens directly when the projector is 

on.

•  The lens cap is for protecting the lens. If you leave 

the lens cap on the lens with the projector turned 
on, it may be deformed because of heat build-up. 
Remove the lens cap when you turn on the projector.

•  The power cords for use in the U.S. and Europe are 

provided with this projector. Use the appropriate 
cord for your country. 

•  This projector uses the power plug of three-pin 

grounding type. Do not remove the grounding pin 
from the power plug. If the power plug doesn't fi t 
your wall outlet, ask an electrician to change the wall 
outlet. 

•  The provided power cord for the U.S. is rated at 120 V. 

Never connect this cord to any outlet or power sup-
ply using other voltages or frequencies than rated. If 
you want to use a power supply using other voltage 
than rated, prepare an appropriate power cord sepa-
rately.

•  Use 100-240 V AC 50/60 Hz to prevent fi re or elec-

tric shock.

•  Do not place any objects on the power cord or do 

not place the projector near heat sources to prevent 
damage to the power cord. If the power cord should 
be damaged, contact your dealer for replacement 
because it may cause fi re or electric shock. 

•  Do not modify or alter the power cord. If the power 

cord is modifi ed or altered, it may cause fi re or elec-
tric shock. 

Caution:
•  Plug in the power cord fi rmly. When unplugging, hold 

and pull the power plug, not the power cord.

•  Do not plug in or out the power cord with your hand 

wet. It may cause electric shock.

For the best projection, project images on a fl at screen 
installed at 90 degrees to the fl oor. If necessary, tilt the 
projector using the two adjustment feet on the bottom 
of the projector. 

 

•  You can correct the vertical and horizontal keystones 

at the same time. However, their adjustment ranges 
are limited in such correction. 

•  When the keystone adjustment is carried out, the 

adjustment value is indicated.  Note that this value 
doesn't mean a projection angle. 

•  The allowable range of the adjustment value in the 

keystone adjustment varies depending on the instal-
lation conditions. 

•  When the keystone adjustment takes effect, the res-

olution decreases. In addition, stripes may appear or 
straight lines may bend in images with complicated 
patterns. They are not due to product malfunctions.  

•  Noise may appear on the screen during the keystone 

adjustment because of the type of the video signal 
being projected and the setting values of the key-
stone adjustment. In such cases, set the keystone 
adjustment values in the range where the image is 
displayed without noise. 

•  When the keystone adjustment is carried out, the im-

age may not be displayed correctly because of the 
type of input signal.

•  When the 1080i signal is input, the keystone adjust-

ment ranges are limited.

Screen

Adjustment feet (Rear)

Press  the 

button.

Press the 

 

button.

Press  the 

(or -) button.

Press the 

 

(or +) button.