Справочник Пользователя для Mitsubishi Electronics colorview xd480u

 

EN - 15

VOLUME     10

Press the VOLUME + or 

- button to change the volume 

from the speaker.
The volume control bar will appear on the screen.

•  The volume control bar will disappear about 10 sec-

onds after the VOLUME button is released.

•  The VOLUME buttons don

't function while the menu 

selection bar or the menu is being displayed. 

•  When a high-level audio signal, such as a DVD audio 

signal, is supplied to the AUDIO IN terminal, the out-
put from the speaker may be distorted.

The video and audio signals are temporarily muted 
when the MUTE button is pressed. To cancel muting, 
press the MUTE button again.
•  If MUTE MODE in the INSTALLATION menu is set 

to IMAGE, the splash screen will appear when the 
MUTE button is pressed. 

•  You can alter the splash screen optionally. See page 

22.

When playing DVD discs containing data of letterboxed 
image, press the 16:9 button. Exit the ANAMORPHIC 
mode, by pressing the 16:9 button again.

Important: 
•  When a letterboxed image is kept displayd for a long 

time before displaying 4:3 image, the afterimages of 
the black bars may appear on the 4:3 image screen. 
Consult your dealer in this case.

Caution: 
•  After using the projector, wait one minute for the air 

outlet fans to stop. Then unplug the power cord from 
the wall outlet.

•  The lamp can

't be lit again for one minute after 

turned off for safety purpose. It will take another one 
minute for the STATUS indicator to go out. If you 
want to turn on the projector again, wait until the in-
dicator goes out, and then press the POWER button.

•  The air outlet fans rotate faster as the temperature 

around the projector rises.

•  When the temperature around the projector rises  

high, the sign 

"TEMPERATURE!!" blinks red on the 

screen. If the temperature stays high, the lamp will 
go out automatically.

Important: 
•  Do not display a still picture for a long time because 

the afterimages may persist on the screen.

Use the following procedure to turn off the projector. Do 
not turn off the projector by unplugging the power cord 
while the lamp is on. Unplugging while the lamp is on 
degrades the lamp

's performance and causes failure in 

the projector. 
1

1

.  Press the POWER button.

• The 

message 

"POWER OFF? YES : PRESS 

AGAIN

" appears on the screen.

•  To cancel, press any button except the POWER 

button. (Some buttons on the remote control 
don

't function for cancel.)

2

2

.  Press the POWER button within 10 seconds again.

•  The lamp will go out and the STATUS indicator 

will start blinking. 

•  Though the lamp goes out at this second press 

of the POWER button, the air outlet fans continue 
operating for one minute to cool down the lamp. 
The STATUS indicator will stop blinking. 

3

3

.  Unplug the power cord.

•  The POWER indicator will go out. 
•  If the power cord should be unplugged acciden-

tally while either the air inlet fan or the air outlet 
fans are operating or the lamp is on, allow the 
projector to cool down for 10 minutes with the 
power off. To light the lamp again, press the 
POWER button. If the lamp doesn

't light up im-

mediately, repeat pressing the POWER button 
two or three times. If it should still fail to light up, 
replace the lamp. 

Important: 
•  When storing the projector in the provided carrying 

case, the lens should face up.

When the image isn

't projected in the right position with 

COMPUTER selected as the input source, follow the 
procedure below. 
1.  Project a bright image such as the  

"Recycle Bin" 

window on the full screen.

2.  If the screen saver is running, turn it off. 

3.  Press the AUTO POSITION button.

•  If the image is still not in the right position, adjust 

the image position using the SIGNAL menu. See 
page 20.