Руководство По Работе для Panasonic KXTG9582
R If you are using a corded headset and a
Bluetooth headset at the same time, the corded
headset is used.
headset is used.
Pairing a headset to the base unit
Important:
R Make sure that the Bluetooth headset is not
R Make sure that the Bluetooth headset is not
connected to any other Bluetooth device.
Handset / Base unit
1
Your headset:
Set your headset to pairing mode.
R Refer to the headset operating instructions.
Set your headset to pairing mode.
R Refer to the headset operating instructions.
2
MMENUN#621
3
If your headset PIN is “0000”, go to step 4.
If your headset PIN is other than “0000”,
press MCLEARN, then enter your headset PIN.
R Typically, default PIN is “0000”. Refer to
If your headset PIN is other than “0000”,
press MCLEARN, then enter your headset PIN.
R Typically, default PIN is “0000”. Refer to
the headset operating instructions.
4
Press MOKN, then wait until a long beep
sounds.
sounds.
5
Proceed with the operation for your unit.
Handset: MOFFN
Base unit: MEXITN
R When the HEADSET indicator on the base
Handset: MOFFN
Base unit: MEXITN
R When the HEADSET indicator on the base
unit lights up, the headset is available for
use.
use.
Connecting/disconnecting a headset
If you cannot connect the headset and base unit
using the headset, you can connect using the unit.
To use your headset with another Bluetooth
device such as a cellular phone, you may need to
disconnect it from the base unit.
If you cannot connect the headset and base unit
using the headset, you can connect using the unit.
To use your headset with another Bluetooth
device such as a cellular phone, you may need to
disconnect it from the base unit.
Important:
R Make sure that the headset is turned on.
R Make sure that the headset is turned on.
Handset
1
To connect/disconnect:
MMENUN#622
R A long beep sounds.
MMENUN#622
R A long beep sounds.
2
MOFFN
Base unit
To connect:
Press MHEADSETN.
To disconnect:
Press and hold MHEADSETN until a long beep
sounds.
Press MHEADSETN.
To disconnect:
Press and hold MHEADSETN until a long beep
sounds.
Unpairing a headset
You can cancel a pairing of the headset that is
stored to the base unit.
You can cancel a pairing of the headset that is
stored to the base unit.
Handset / Base unit
1
MMENUN#612
2
MbN: “Yes” a MSELECTN
R When the headset is unpaired, the
R When the headset is unpaired, the
HEADSET indicator on the base unit is
turned off.
turned off.
3
Proceed with the operation for your unit.
Handset: MOFFN
Base unit: MEXITN
Handset: MOFFN
Base unit: MEXITN
Operating a Bluetooth wireless
headset using a landline
headset using a landline
Important:
R Refer to your headset operating instructions for
R Refer to your headset operating instructions for
headset operations.
Answering landline calls with your headset
To answer a landline call, turn on your headset
referring to your headset operating instructions.
When you finish talking, turn off your headset
referring to your headset operating instructions.
To answer a landline call, turn on your headset
referring to your headset operating instructions.
When you finish talking, turn off your headset
referring to your headset operating instructions.
Note:
R If you cannot hang up the call using your
R If you cannot hang up the call using your
headset, press MZN on the base unit 2 times.
Switching between the base unit and your
headset
You can switch between the base unit and your
headset:
– during a landline call with the base unit
headset
You can switch between the base unit and your
headset:
– during a landline call with the base unit
speakerphone.
– during an intercom call between the base unit
and handset.
– while listening to messages recorded on the
base unit answering system.
n
To switch to your headset:
Press MHEADSETN on the base unit.
Press MHEADSETN on the base unit.
n
To switch to the base unit:
Press MZN on the base unit.
Press MZN on the base unit.
For assistance, please visit http://shop.panasonic.com/support
59
Using Bluetooth® Devices
TG95x_OI(en-en)_0722_ver110.pdf 59
2015/07/22 12:33:24