Инструкция для Panasonic tu-cth100
TU-CTH100
3
Warnings and Precautions
This Personal Digital Video Recorder (PVR) is intended for the reception of Digital TV picture and sound signals. If the
PVR is exposed to drastic temperature changes, e.g. taking it from a cold room to a warm room, connect it to the mains
supply and let it stand for at least two hours. Do not expose the PVR to any moisture. The PVR is designed for use
indoors and should be protected against moisture (splashes of water etc.).
Do not expose the PVR to dripping or splashing water and objects filled with liquid, such as vases, must not be placed on
top of or above the unit. Adequate ventilation is essential to prevent failure of electrical components; we recommend that
a gap of at least 5cm is left all around this PVR even when it is placed inside a cabinet or between shelves. Ensure that
the ventilation holes beneath the unit are not blocked.
Do not place the PVR unit in the immediate vicinity of a heat source or in direct sunlight as this would prevent appropriate
cooling.
To prevent fire, never place any type of candle or naked flame on top of or near the PVR.
Caring for your PVR
Remove the mains plug from the wall socket. The cabinet can be cleaned with a dry, clean cloth. Do not use solutions
containing benzol or petroleum.
Make sure that all the electrical connections are properly made. Do not connect any of your equipment (TV, video
recorder, etc.) to the mains supply until you have properly connected all the other leads. Disconnect your PVR from the
mains supply before you disconnect any other equipment from its rear panel.
Safety Warning
Do not remove outer cover.
Touching internal parts of the unit is dangerous, and may seriously damage it.
To prevent electric shock, do not remove cover. There are no user serviceable parts inside.
Refer all servicing to qualified service personnel.
PVR is exposed to drastic temperature changes, e.g. taking it from a cold room to a warm room, connect it to the mains
supply and let it stand for at least two hours. Do not expose the PVR to any moisture. The PVR is designed for use
indoors and should be protected against moisture (splashes of water etc.).
Do not expose the PVR to dripping or splashing water and objects filled with liquid, such as vases, must not be placed on
top of or above the unit. Adequate ventilation is essential to prevent failure of electrical components; we recommend that
a gap of at least 5cm is left all around this PVR even when it is placed inside a cabinet or between shelves. Ensure that
the ventilation holes beneath the unit are not blocked.
Do not place the PVR unit in the immediate vicinity of a heat source or in direct sunlight as this would prevent appropriate
cooling.
To prevent fire, never place any type of candle or naked flame on top of or near the PVR.
Caring for your PVR
Remove the mains plug from the wall socket. The cabinet can be cleaned with a dry, clean cloth. Do not use solutions
containing benzol or petroleum.
Make sure that all the electrical connections are properly made. Do not connect any of your equipment (TV, video
recorder, etc.) to the mains supply until you have properly connected all the other leads. Disconnect your PVR from the
mains supply before you disconnect any other equipment from its rear panel.
Safety Warning
Do not remove outer cover.
Touching internal parts of the unit is dangerous, and may seriously damage it.
To prevent electric shock, do not remove cover. There are no user serviceable parts inside.
Refer all servicing to qualified service personnel.
Notes on these instructions
Company names, product names and all other names in these instructions are the trademarks or registered trademarks
of their respective corporations.
The contents of the screens used in these instructions may not necessarily match what you will see on your screen.
Company names, product names and all other names in these instructions are the trademarks or registered trademarks
of their respective corporations.
The contents of the screens used in these instructions may not necessarily match what you will see on your screen.
Hard Disk Drive (HDD) Warning and Precautions
Follow the precautions indicated below to prevent damage to the internal HDD. (Not following precautions may
result in a loss of recording, stop of operation or recording of noise.)
While in operation
Do not disconnect the AC mains supply.
Do not move the unit or subject it to vibration or impact.
When moving the unit:
1. Press the Standby On/Off key to power the PVR to standby. (Wait until the front panel displays the curent time.)
2. Remove the AC mains plug from the mains socket.
3. Wait 2 minutes before moving.
While the unit is on, the HDD will be spinning at high speed and it is normal to hear some low level sounds. These
sounds are not problems.
In the event of a power failure
If a power failure occurs, the contents of the HDD may be damaged.
To prevent accidental loss of HDD content
Data may be lost if the HDD suffers damage. Any contents you wish to keep permanently should be dubbed or moved to
storage media. (see page 28)
HDD SLEEP mode
When the PVR is placed into standby, the HDD is placed into Sleep mode.
At Power up, the HDD will take a short period to start, during this time some menus and features will not be available.
HDD remaining time
Due to the recording compression, the amount of actual space left on the HDD may not match the amount shown on
screen. To free up more space on the HDD, please delete some recordings.
result in a loss of recording, stop of operation or recording of noise.)
While in operation
Do not disconnect the AC mains supply.
Do not move the unit or subject it to vibration or impact.
When moving the unit:
1. Press the Standby On/Off key to power the PVR to standby. (Wait until the front panel displays the curent time.)
2. Remove the AC mains plug from the mains socket.
3. Wait 2 minutes before moving.
While the unit is on, the HDD will be spinning at high speed and it is normal to hear some low level sounds. These
sounds are not problems.
In the event of a power failure
If a power failure occurs, the contents of the HDD may be damaged.
To prevent accidental loss of HDD content
Data may be lost if the HDD suffers damage. Any contents you wish to keep permanently should be dubbed or moved to
storage media. (see page 28)
HDD SLEEP mode
When the PVR is placed into standby, the HDD is placed into Sleep mode.
At Power up, the HDD will take a short period to start, during this time some menus and features will not be available.
HDD remaining time
Due to the recording compression, the amount of actual space left on the HDD may not match the amount shown on
screen. To free up more space on the HDD, please delete some recordings.