Инструкции Пользователя для ONKYO PR-RZ5100

Troubleshooting | Appendix

Setup

1. Input/Output Assign 
2. Speaker
3. Audio Adjust
4. Source
5. Hardware
6. Multi Zone

7. Miscellaneous

1. Tuner
2. Remote ID
3. Preamp Mode

4. Firmware Update

5. Initial Setup
6. Lock

Setup

1. Input/Output Assign 
2. Speaker
3. Audio Adjust
4. Source
5. Hardware
6. Multi Zone

7. Miscellaneous

1. Tuner
2. Remote ID

3. Firmware Update

4. Initial Setup
5. Lock

•  If "Firmware Update" is grayed out and cannot be 

selected, wait for a while until it starts up.

•  You will not be able to select "Update via NET" if 

there is nothing to update.

3.  Press ENTER with "Update" selected to start update.

•  During the update, the TV screen may go black 

depending on the updated program. In that case, 

check the progress on the display of the unit. The 

TV screen will remain black until the update is 

complete and the power is turned on again.

•  "Completed!" is displayed when the update is 

complete.

4.  Press  ON/STANDBY on the main unit to turn the unit 

into standby mode. The process is completed and your 

firmware is updated to the latest version.

•  Do not use   on the remote controller.

■ If an Error Message is Displayed

When an error occurs, "＊-＊＊ Error!" is displayed on 

the display of the unit. ("＊" represents an alphanumeric 

character.) Check the following:
Error Code

•  ＊-01, ＊-10：

Ethernet cable not found. Connect the Ethernet cable 

properly.

•  ＊-02, ＊-03, ＊-04, ＊-05, ＊-06, ＊-11, ＊-13,  ＊-14, ＊

-16, ＊-17, ＊-18, ＊-20, ＊-21：

Internet connection error. Check the following:

–  The router is turned on

–  This unit and the router are connected via the 

network

Try to disconnect and then connect again the power 

to the unit and router. This may solve the problem. If 

you are still unable to connect to the Internet, the DNS 

server or proxy server may be temporarily down. Check 

the service status with your ISP provider.

Disconnect then reconnect the AC power cord, then 

repeat from the beginning.

Preparation: 

•  Prepare a 128MB or larger USB storage device. FAT16 

or FAT32 file system format.

–  Media inserted in a USB card reader may not be 

used for this function.

–  USB storage devices with security function are not 

supported.

–  USB hubs and USB devices with hub function are 

not supported. Do not connect these devices to the 

unit.

•  Delete any data stored on the USB storage device.

•  Turn off the controller component (PC etc.) connected 

to the network.

•  Stop any playing Internet radio, USB storage device, or 

server content.

•  If the multi-zone function is active, turn it off.

•  If "HDMI CEC" is set to "On", set it to "Off".

–  Press   on the remote controller. Then, after 

selecting "5. Hardware" - "HDMI" and pressing 

ENTER, select "HDMI CEC" and select "Off".

＊

 Some USB storage devices may take long to load, may not be loaded 

correctly, or may not be correctly fed depending on the device or their 

content.

＊

 Our company will not be liable whatsoever for any loss or damage of 

data, or storage failure arising from the use of the USB storage device 

with this unit. Thank you for your understanding.

＊

 The description may differ from the on-screen display but that will not 

change the way to operate or the function.

■ Update

1.  Connect the USB storage device to your PC.
2.  Download the firmware file from our company's website 

to your PC and unzip.

Firmware files are named in the following way:

 ONKAVR＊＊＊＊_＊＊＊＊＊＊＊＊＊＊＊＊.zip

Unzip the file on your PC. The number of unzipped files 

and folders varies depending on the model.

3.  Copy all unzipped files and folders to the root folder of 

the USB storage device.

•  Make sure to copy the unzipped files.