Справочник Пользователя для Datastrip Inc. DSV2SC01
DSV2+
Turbo
User Manual, Version 1.09
32
Copyright © 2006 by Datastrip, Inc. All rights reserved.
Reproduction in whole or in part is prohibited.
•
Select most recent appropriate source file (Ex. Src File: \DSVII_0195_sh4.CAB)
•
Click Download and wait for message “Download complete”
•
Click Update
•
Click Reboot
•
Power up unit
•
The DSV2+ registration program will automatically open. Select the button for the
device that you are registering (DSVII-SC, DSVII-PA, or DSVII-SW). Select [OK] and
wait. (This process can take from a few seconds to up to 45 seconds).
wait. (This process can take from a few seconds to up to 45 seconds).
•
Click [Ok] in the “Hurray!” Box when it appears, then close the application window.
•
Double tap My Computer and Select Storage Card / DSVII.
•
Double tap the RegistrySaver program.
•
Double tap the PPCalFt41utility and press the “Calibrate” button to initialize the
fingerprint sensor. This process may take up to a minute and then a “green” window with
a number “1” should appear to indicate the sensor was successfully calibrated.
a number “1” should appear to indicate the sensor was successfully calibrated.
•
Double tap the DsVerifyFpCaptureTest application. In the lower right hand corner select
“UPEK” and click “OK”. DO NOT use the calibrate button on this screen for UPEK,
however you can use the Scan function to test the fingerprint image.
however you can use the Scan function to test the fingerprint image.
•
If you are upgrading a scanner go to Section 8.2
8.2 Loading Scanner Firmware Updates
The DsVerify2ScannerUpdate utility is used to update the DSP firmware in the scanner-based
versions of DSV2+ by installing runtime files of the proper form (.hex extension) which have
been generated by Datastrip.
versions of DSV2+ by installing runtime files of the proper form (.hex extension) which have
been generated by Datastrip.
•
Check that the Scanner Firmware provided is compatible for use with the unit by looking
at the DSVII Software Release Notes for the Run-Time software. The version of the
scanner firmware can be checked in the DatastripDsVerify2About application under the
name “ScanVer”.
scanner firmware can be checked in the DatastripDsVerify2About application under the
name “ScanVer”.
•
In the directory Storage Card/DSVII run the utility DsVerify2ScannerUpdate.exe.
•
Using the button marked […]; select by, double clicking, the appropriate scanner runtime
DSP binary file (.hex) that is to be loaded into the scanner sub-system. The latest copy is
usually found in the Storage Card -> DSVII -> DSVII_Scanner_DSP directory. (Ex. Src
File: \DSVII_Scanner_Runtime_Ver_152.Hex)
usually found in the Storage Card -> DSVII -> DSVII_Scanner_DSP directory. (Ex. Src
File: \DSVII_Scanner_Runtime_Ver_152.Hex)
•
Once the appropriate file has been chosen, click the Verify button to validate the format
and checksums for the file.
•
Click the Update button to download the file to the scanner DSP engine.
•
When the status message indicates “Scanner Update Complete”, Exit the application.
•
To confirm the new version has been loaded use the DatastripDsVerify2About.exe
application to check the “ScanVER” entry, which should match the release number of the
(.hex) file that was just loaded.
(.hex) file that was just loaded.
•
Reboot the unit by pressing Power Off button.
8.3 Loading Smartcard Firmware Updates
Smartcard firmware version 5.12 cannot be erased and therefore does not support the update
procedure. Only ScardFw versions 6.32 or later can be updated. Verify the version of your
SCardFw by running the DsVerify2About Utility. The procedure for updating the smartcard
firmware is as follows:
procedure. Only ScardFw versions 6.32 or later can be updated. Verify the version of your
SCardFw by running the DsVerify2About Utility. The procedure for updating the smartcard
firmware is as follows: