Справочник Пользователя для Redline Communications Inc. AN100UXA
User
AN-100U/UX Base Station
Manual
70-00058-01-04
Proprietary Redline Communications © 2010
Page 70 of 136
April 19, 2010
DHCP Relay Agent Parameters
The subscriber can obtain an IP address from the DHCP server only through a base
station acting as a DHCP Relay Agent. A subscriber can not obtain an IP address from
any DHCP server on the network segment connected to its local Ethernet port. The base
station (acting as a DHCP Relay Agent) can be configured for two different modes:
station acting as a DHCP Relay Agent. A subscriber can not obtain an IP address from
any DHCP server on the network segment connected to its local Ethernet port. The base
station (acting as a DHCP Relay Agent) can be configured for two different modes:
SS-s should use the same DHCP Server as SC: Select this option to have the base
station forward all subscriber DHCP requests to the DHCP server that the base station
used to obtain its IP address (valid only if field Obtain IP Parameters from DHCP Server
is enabled above).
station forward all subscriber DHCP requests to the DHCP server that the base station
used to obtain its IP address (valid only if field Obtain IP Parameters from DHCP Server
is enabled above).
SS-s should use the following DHCP Server: Select this option to specify the DHCP
server to be used by subscribers.
server to be used by subscribers.
DHCP Server: Specify the IP address of a DHCP server. The base station forwards
all subscriber DHCP requests to this address.
all subscriber DHCP requests to this address.
It important to configure the correct lease options on your DHCP Server:
a) The subscriber requires option 4, the address of a ToD Server (RFC-868).
b) If you do not wish your devices to display GMT, you must add option 2 (Time Offset).
This is a value denoting the number of seconds to offset your time from GMT. For
example, for the offset of +2 hours you should enter 7200 (some DHCP servers may
require entering hexadecimal value). In North America, EST is -5 hours (-18000
seconds) from GMT and the negative value must be entered.
This is a value denoting the number of seconds to offset your time from GMT. For
example, for the offset of +2 hours you should enter 7200 (some DHCP servers may
require entering hexadecimal value). In North America, EST is -5 hours (-18000
seconds) from GMT and the negative value must be entered.
Important: The base station must be rebooted to activate changes to the DHCP Relay
Agent settings.
Agent settings.
VLAN Management
Enable Management with VLAN Tagged Traffic: Check to manage the AN-100U/UX
using VLAN tagged traffic. This feature can be used where a single management VLAN
is used to manage the base station wireless equipment and user equipment. After
enabling this feature, only traffic with the specified VID is recognized for any
management commands. This setting does not affect operation of the RS-232 Console
port.
using VLAN tagged traffic. This feature can be used where a single management VLAN
is used to manage the base station wireless equipment and user equipment. After
enabling this feature, only traffic with the specified VID is recognized for any
management commands. This setting does not affect operation of the RS-232 Console
port.
Important: Network support for VLAN should be verified before enabling this
feature. If the base station is not reachable using the VLAN tagged traffic, the
Console port (RS-232) CLI command must be used to disable this setting.
feature. If the base station is not reachable using the VLAN tagged traffic, the
Console port (RS-232) CLI command must be used to disable this setting.
VLAN ID: Enter the VID of the VLAN to be used for management traffic. When
Management with Tagged Traffic is enabled, only traffic tagged with this VLAN ID is
recognized by the sector controller management process.
Management with Tagged Traffic is enabled, only traffic tagged with this VLAN ID is
recognized by the sector controller management process.
Save: Click
Save
to save and apply the current settings.
Cancel: Click
Cancel
to discard all changes and return to the main screen.
Default: Click
Default
to set all settings to the factory default settings.