Справочник Пользователя для SPAL USA RCU6RX
YELLOW
RED
BLUE / WHITE
GRAY
YELLOW / RED
BLUE
WHITE
WHITE / BLACK
FUSE
(1) Receiver
(2) Remotes
(2) Wire Harnesses
2
Installation Instructions for
RCU6
This kit is designed to operate six functions via the 6-button remote controls.
These channels can be used to operate power door locks, power door releases, trunk
releases, control linear actuators, or roll up or down power windows.
releases, control linear actuators, or roll up or down power windows.
All channels can be Positive or Negative outputs depending on how the input
wire is connected. Please refer to the diagrams on page __?_ of this instruction
manual for positive, and negative, wiring diagrams and other recommendations, such
as reverse polarity for power windows.
manual for positive, and negative, wiring diagrams and other recommendations, such
as reverse polarity for power windows.
**Proper wiring is critical to the correct operation of this product. Make sure all wires
are properly connected, properly grounded, free of potential damage, and are correctly
fused**
are properly connected, properly grounded, free of potential damage, and are correctly
fused**
FUSE
Each Kit Contains The Following Components
B
Y
R
TT
A
E
Output From Receiver
87A
86
85
30
87
+ 12 VDC
FUSE
30
87A
87
85
86
Output From Receiver
Power Window
Motor
Motor
S
W
I
T
C
H
C
H
4
Y
T
B A
T E R
85
86
30
87
Output From Receiver
87A
+ 12 VDC Output
+ 12 VDC
FUSE
Optional Wiring Diagrams
Positive Output
Negative Output
Reverse Polarity Output
T
B AT
Y
E R
Output From Receiver
86
Ground Output
30
87A
87
85
GROUND
FUSE
+ 12 VDC
FOR POWER WINDOWS TWO RELAYS MUST BE PLACED BETWEEN THE SWITCH AND THE
WINDOW MOTOR. THE DASHED LINES INDICATE WHERE THE WIRES MUST BE CUT.
WINDOW MOTOR. THE DASHED LINES INDICATE WHERE THE WIRES MUST BE CUT.
5
W
I
R
E
W
I
R
E
S
W
I
T
C
H
W
I
T
C
H
**In a reverse polarity system, a switch that rests at ground must be used.**
Positive Output
To Device
Ground Output
To Device
V
III
I
VI
IV
II
Negative Output From Receiver
Positive Output From Receiver
FCC ID INFORMATION
FCC ID#: KNF6TX
"This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation."
"This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation."
Industry Canada
IC ID#: XXXXXX-6TX (XXXXXX will be replaced with the company number issued by Canada)
“The term “IC:” before the radio certification number only signifies that Industry Canada technical
specifications were met.”
IC ID#: XXXXXX-6TX (XXXXXX will be replaced with the company number issued by Canada)
“The term “IC:” before the radio certification number only signifies that Industry Canada technical
specifications were met.”
Disclaimer Statement
Caution: changes or modifications not expressly approved by SPAL USA will void the user's
authority to operate the equipment.
Caution: changes or modifications not expressly approved by SPAL USA will void the user's
authority to operate the equipment.
V
III
I
VI
IV
II