Справочник Пользователя для SPAL USA RCU6RX
Reprogramming the Remote Transmitters:
**This RCU6 can accept up to 4 SPAL remote transmitters (Part # RCU6TX)**
The remote transmitters are shipped Pre-Programmed. In the event that a remote
transmitter loses the programmed code, or if you wish to add more remote
transmitters, follow these instructions:
The remote transmitters are shipped Pre-Programmed. In the event that a remote
transmitter loses the programmed code, or if you wish to add more remote
transmitters, follow these instructions:
•Make sure ignition is OFF.
•Locate the programming button located on the side of the receiver, next to the LED.
•Press the programming button 3 times (The LED will light).
•Press Button 1 on each remote you wish to program (The LED will turn off for a
•Locate the programming button located on the side of the receiver, next to the LED.
•Press the programming button 3 times (The LED will light).
•Press Button 1 on each remote you wish to program (The LED will turn off for a
moment, then back on with each remote transmitter it recognizes)
•The LED will remain lit for approx. 10 seconds after the last remote transmitter
has been recognized.
•Wait for the LED to go out. Then test each remote transmitter for proper function.
To Operate:
Press:
Channel 1
Button I
Channel 2
Button II
Channel 3
Button III
Channel 4
Button IV
Channel 5
Button V
Channel 6
Button VI
Basic Function of the SPAL Shaved Door Kit
The remote control supplied with your kit has four buttons, but is capable of controlling
6 channels.
Channel 1:
Channel 2:
Channel 3:
Channel 4:
Channel 5:
Channel 6:
Channel 1:
Channel 2:
Channel 3:
Channel 4:
Channel 5:
Channel 6:
Operation Section
Programming Section
3
Basic Functions Of The Remote Control
5
Optional Wiring Section
Item to be
Description
Relay Type
# of Relays
Diagram
Activated
of Function
Required
1 Power window motor
Move window up & down
SPDT
2
Reverse
1 Power window motor
Move window one direction
SPDT
1
Reverse
Linear actuator
Move in & out
SPDT
2
Reverse
Solenoid
Activate Solenoid
SPST
1
Positive or Negative
Trunk Release
Open the Trunk
SPST
1
Positive or Negative
Door lock actuator
Lock & unlock
SPDT
2
Reverse
SPST
= Single pole single throw relay, 30 or 40 amp
SPDT
= Single pole double throw relay 30 or 40 amp
Relays can either be purchased from SPAL USA or from your local auto parts store.
Wiring Options
Positive outputs are +12VDC
Negative outputs are ground
Both outputs are capable of handling 10Amps
Negative outputs are ground
Both outputs are capable of handling 10Amps
V
III
I
VI
IV
II
Receiver Mounting and Wiring:
**The receiver must be mounted inside the vehicle to avoid moisture**
**Do not plug in the receiver module until all the wiring is complete**
**Do Not Ground the Antenna**
**Do not plug in the receiver module until all the wiring is complete**
**Do Not Ground the Antenna**
ANTENNA
GND
+12V
LED
PROGRAMMING BUTTON
YELLOW
RED
BLUE / WHITE
GRAY
YELLOW / RED
BLUE
WHITE
WHITE / BLACK
+12V
IGN
CH 6 OUTPUT
CH 4 OUTPUT
CH 2 OUTPUT
CH 5 OUTPUT
CH 1 OUTPUT
CH 3 OUTPUT
FUSE
FUSE
Mounting / Wiring Section
Connector 1
Connector 2
Pin #
Wire Color
Circuit
Wire Color
Circuit
1
Red
Input
Red
Positive 12 VDC
2
Yellow
Ignition
Black
Ground
3
Blue/White
Channel 6
4
Gray
Channel 4
5
Yellow/Red
Channel 2
6
Blue
Channel 5
7
White
Ignition 1
8
White/Black
Channel 3
ANTENNA
GND
+12V
PROGRAMMING BUTTON
LED
RED
GROUND
IGN
CH 6 OUTPUT
CH 4 OUTPUT
CH 3 OUTPUT
CH 1 OUTPUT
CH 5 OUTPUT
CH 2 OUTPUT
GRAY
BLUE
WHITE / BLACK
WHITE
YELLOW / RED
BLUE / WHITE
YELLOW
FUSE
FUSE
Positive Output
Negative Output