Справочник Пользователя для Digital Monitoring Products Inc PC0126P

All keypads provide Keypad Option and Keypad Diagnostic menus to allow installing and service technicians to configure 

and test keypad operation.

Access the Installer Options Menu through the User Options function.  Hold down the Back Arrow and COMMAND keys for 

two seconds to display SET BRIGHTNESS.  Enter the code 3577 (INST) and press COMMAND.  The display changes to KPD OPT 

(keypad options) KPD DIAG (keypad diagnostics) and STOP.
The Keypad Options menu allows you to set the keypad address, select Supervised or Unsupervised mode, change the 

default keypad message, selectively enable the 2-button Panic keys. 
Note: All programming options display on all keypads, however, actual operation for some programming options is 

restricted to the listed keypads.

Kpd Kpd

Opt diag 

  StOp

To program keypad options, press the left Select key under KPD OPT.  

CUrrent Keypad

addreSS:    

01

Set the keypad address from 01 to 04 with the XTL panel.  The factory default address is set at 

01.  To change the current address, press any Select key and enter the new address.  It is not 

necessary to enter a leading zero for addresses 01 to 04.

deFaULt Keypad 
MSg:

Enter a custom message of up to 16 characters to appear on the keypad display top line 

whenever that line is not used for any other purpose.  Press any Select key to clear the current 

message and enter a new custom display.

arM paniC KeyS:

*pn  *eM  *Fi

Use this option to configure the top row Select keys as 2-button Panic keys.  To enable 

or disable a Panic, press the Select key under the appropriate display: PN (Panic), EM 

(Emergency), and FI (Fire).  Once the panic is enabled, an asterisk displays next to the 

description.  Refer to the Panic Key Options section earlier in this document.

aLL?: 

  nO  yeS

deLay:   

 

2

Select the number of seconds (1-9) the keypad should wait when an area system displays ALL?  

NO  YES during arming/disarming or a HOME/SLEEP/AWAY system waits during arming only.  If 

NO or YES, or HOME,  SLEEP, or  AWAY is not manually selected before the delay expires, the 

keypad automatically selects the YES or the AWAY key.  Select zero (0) to disable this feature.  

This delay only occurs when any credential is presented for arming the Home/Sleep/Away 

system.  

The following options are for programming the proximity credential for the Model 9063 only.

Card OptiOnS

dMp 

  CUStOM

Select DMP to indicate the reader sends a 26-bit DMP data string.  To save the DMP option, 

press the left top row Select key under DMP.  Default is DMP.
Select CUSTOM if using a non-DMP credential.  To select CUSTOM press the right top row Select 

key. 

Wiegand COde 
Length:  

 

26

When using a custom credential, enter the total number of bits to be received in Wiegand code 

including parity bits.  Press any top row Select key to enter a number between 0-255 to equal 

the number of bits.  Default is 26 bits.
Typically, an access card contains data bits for a site code, a user code, and start/stop/parity 

bits.  The starting position location and code length must be determined and programmed into 

the keypad.

0 1 1 1 0 1 0 1 1 0 1 1 0 1 0 1 0 0 0 1 1 0 0 1 1 1

First Bit

Received

Position = 0

Site Code

Position = 1

Length = 8

User Code

Position = 9

Length = 16

Last Bit

Received

Position = 25

In this example the Wiegand Code Length = 26 bits.