Справочник Пользователя для UTC Fire & Security Americas Corporation Inc 612-H20PANIC

Learn Mode Water Resistant Pendant Panic Button Installation Instructions

Programming

This section describes the basic steps for adding the sensor to

panel memory. For complete instructions, refer to the specific

panel’s documentation.

To program the sensor:

1. Set the panel in program mode.

2. When prompted by the panel, enter the appropriate group

number (groups 00 through 07).

Note: For UL installations where the holder is used, the

sensor must be added as a fixed type (sensor groups 00,

02, 04, or 05).

3. When prompted by the panel, select the desired sensor

number.

4. When prompted by the panel, trip the sensor by pressing

the sensor button.

5. Exit from program mode.

Sensor test

To test the sensor:

1. Set the system to the Dealer Sensor Test mode.

2. Press the button on the sensor.

3. Count the number of signals received by the panel,

indicated by interior siren beeps. Seven to eight beeps are

considered acceptable.

4. Test the sensor from several locations within the premises

to check for consistent response.

Battery replacement

To replace the sensor battery:

1. To disassemble the sensor, remove the two screws on the

back of the sensor and separate the front and back plastic.

Caution:

You must be free of static electricity before handling

the transmitter circuit board. Touch a grounded, bare metal

surface before touching the circuit board, or wear a grounding

strap.

2. Remove the old battery from its holder and install the new

battery, observing polarity

Caution:

Install only the same size and type of battery. Do not

substitute another size or type of battery.

3. Reassemble the sensor.

Note: Be sure to assemble the sensor correctly to ensure

water resistance. Be especially careful not to nick or

damage the rubber gasket lining.

4. Test the sensor as described in “Sensor test” above.

Lithium battery disposal

Lithium batteries that are no longer usable are considered

hazardous waste. Be sure to properly dispose of the old

battery. Contact your local city government for hazardous

waste disposal laws.

Specifications

Compatibility

All Interlogix Security Learn Mode panels

Power source

3.6 VDC Saft or Tekcell lithium battery

Enclosure

Water-resistant and shock-resistant

Dimensions (LxWxD)

2.25 x 1.75 x 0.75 in. (5.71 x 4.44 x 1.90 cm)

Regulatory information

Manufacturer

UTC Fire & Security Americas Corporation, Inc.
1275 Red Fox Rd., Arden Hills, MN 55112-6943,
USA

FCC compliance

This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
Changes or modifications not expressly approved
by Interlogix can void the user’s authority to
operate the equipment.

FCC ID: B4Z-612-H2OPANIC

IC compliance

IC: 1175C-612PANIC

This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
Le fonctionnement est soumis aux deux
conditions suivantes : (1) cet appareil peut ne pas
provoquer d’interférences et (2) cet appareil doit
accepter toutes interférences, y compris les
interférences pouvant provoquer un
fonctionnement non désiré de l’appareil.

U.S. patents

4,855,713, 4,864,636, and others pending.

Contact information

For contact information, see www.utcfireandsecurity.com or

www.interlogix.com.

For technical support, toll-free: 888.437.3287 in the US

including Alaska, Hawaii, Puerto Rico, and Canada. Outside

the toll-free area, contact your dealer.