Справочник Пользователя для UTC Fire & Security Americas Corporation Inc 924-2WTTS
4. When the panel displays Enter Code, enter the appropriate
code and press OK.
5. When the panel displays Sensor Test, press OK to start
the sensor test.
The panel will prompt you to trip each sensor one at a time.
6. To trip the touch screen,
XXXXXXXXXXX
.
You can follow the panel voice prompting to test the sensors
in any order.
in any order.
We recommend that you test the touch screen after all
programming is completed and whenever a touch screen related
problem occurs.
programming is completed and whenever a touch screen related
problem occurs.
To verify communication between the panel and the touch screen,
close the panel’s cover to put the panel in run mode and then
press the System Status icon on the touch screen. The touch
screen should announce the correct system status.
close the panel’s cover to put the panel in run mode and then
press the System Status icon on the touch screen. The touch
screen should announce the correct system status.
Sensor test failure
If panel sirens do not beep when a touch screen is tripped, use a
GE RF sniffer (60-401) test tool to verify that the touch screen is
transmitting. Constant beeps from the RF sniffer indicate a faulty
touch screen. Two or three beeps from the RF sniffer indicate the
touch screen is functioning but may have to be relocated.
GE RF sniffer (60-401) test tool to verify that the touch screen is
transmitting. Constant beeps from the RF sniffer indicate a faulty
touch screen. Two or three beeps from the RF sniffer indicate the
touch screen is functioning but may have to be relocated.
To relocate the touch screen:
1. Test the touch screen a few inches from the original position.
2. Increase the distance from the original position. Retest until
an acceptable location is found.
3. Mount the touch screen in the new location (see Mounting).
Test a known good touch screen at the same location.
•
If transmission beeps remain below the minimum level, avoid
mounting a touch screen at that location.
mounting a touch screen at that location.
•
If the replacement touch screen functions, contact GE
Security for repair or replacement of the faulty touch screen.
Security for repair or replacement of the faulty touch screen.
Mounting
To mount the touch screen:
1.
XXXXXXXXXXXXXXXXXXX
2.
XXXXXXXXXXXXXXXXXX
3.
XXXXXXXXXXXXXXXXXXX
Operation
Refer to the touch screen Quick Operation Guide for operation
information.
information.
Battery replacement
When the touch screen batteries are low, the touch screen
announces Touch Screen Low Battery. The panel announces
(sensor name) Low Battery. Remove the touch screen from the
mounting plate and replace all batteries. Avoid touching the touch
screen face while you are replacing the batteries. After replacing
announces Touch Screen Low Battery. The panel announces
(sensor name) Low Battery. Remove the touch screen from the
mounting plate and replace all batteries. Avoid touching the touch
screen face while you are replacing the batteries. After replacing
the batteries, do a sensor test to realign the touch screen with the
panel.
panel.
Specifications
Compatibility
Simon XT (version 1.3 and later)
Power
XXXXX
Battery
Type
Replace
Type
Replace
with
Voltage, chemistry, form factor
Manufacturer P/N, Manufacturer P/N, or GE
approved equivalent
Manufacturer P/N, Manufacturer P/N, or GE
approved equivalent
Dimensions (W × H × D)
0.0 × 0.0 × 0.0 in. (000 × 000 × 000 mm)
Operating environment
Temperature
Relative
Temperature
Relative
humidity
00 to 00°F (00 to 00°C)
0 to 00% noncondensing
0 to 00% noncondensing
Regulatory information
FCC
This device complies with part 15 of the FCC rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference.
Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference
received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
FCC ID:
XX
IC:
XX
Contact information
For contact information see our Web site: www.gesecurity.com.
2 of 2
P/N 000000 • REV 00.01 • ISS 11DEC09
Draft