Справочник Пользователя для CCL ELECTRONICS LTD 3110A1703
GETTING STARTED
WIRELESS SENSOR
WIRELESS SENSOR
1. Remove the battery door of the sensor.
2. Insert 2 x AA size batteries into the battery compartment. Make
sure you insert them the right way according to the polarity
information marked on the battery compartment.
3. Close the battery door.
Note:
- Once the channel is assigned to one sensor, you can only
change it by removing the batteries or resetting the unit.
- Avoid placing the sensor in direct sunlight, rain or snow.
MAIN UNIT
1. Remove the battery door of the main unit.
2. Install 4 new AA size batteries according to the polarity
information marked on the battery compartment and then press
[ RESET ] key by using a metal wire to reset the unit.
3. Close the battery door.
4. Once the batteries are installed, all the segments of the LCD will
be shown.
Note:
To avoid the wireless sensor and main unit pairing failure, please
power up the sensor/s first, and then press
[ RESET ] key on the
main unit (no need on sensors).
INDOOR TEMPERATURE AND HUMIDITY FUNCTION
1. Press
1. Press
[ °C / °F ] key to switch between °C / °F. Decimal point is
effective for both settings.
2. When the temperature is below -40°F or above 158°F, “
Lo” or
“
Hi” will be displayed respectively. The humidity display will show
“
--”.
Temperature below -40°C
Temperature above 70°C
3. When the humidity is below 1% or above 99%, “
Lo” or “Hi” will be
indicated respectively.
Humidity below 1%
Humidity above 99%
COMFORT INDICATION
The comfort indication is a pictorial indication based on indoor air
The comfort indication is a pictorial indication based on indoor air
temperature and humidity in an attempt to determine comfort level.
Too cold
Comfortable
Too hot
Note:
- Comfort indication can vary under the same temperature,
depending on the humidity.
- There is no comfort indication when temperature is below 0°C
(32°F) or over 60°C (140°F).
TEMPERATURE & HUMIDITY TREND
The temperature & humidity trend indicator shows the trends of
The temperature & humidity trend indicator shows the trends of
changes in the forthcoming few minutes. Arrows indicate a rising,
steady or falling trend.
Arrow indicator
Trend
Trend
Rising
Steady
Falling
TEMPERATURE AND HUMIDITY CALIBRATION
1. In normal mode, press and hold
1. In normal mode, press and hold
[ TUNE ] key for 2 seconds to
enter temperature and humidity calibration mode in which the
current outdoor channel or “
IN” icon will flash. Press [ CHANNEL
/ + ] or [ MEM / - ] key to choose for INDOOR or different
CHANNEL.
Choose Channel
2. Press
[ MODE ] key again to switch between temperature and
humidity. Press
[ CHANNEL / + ] or [ MEM / - ] key to adjust the
value.
3. When finished, press
[ TUNE ] key for 2 seconds or leave the unit
for 60 seconds to return to normal mode.
4. Pressing
[ MODE ] key for 2 seconds during temperature and
humidity calibration mode will reset the value to the actual or
uncalibrated measurement.
5. Reset the temperature and humidity values for each channel
individually. There is no batch reset.
6. Calibration mode sequence: channel → temperature → humidity
7. In temperature calibration mode, press
[ CHANNEL / + ] key or
[ MEM / - ] key to modify 0.1 °C or °F of the value. Long press to
quick-adjust the value.
Temperature calibration mode
8. In humidity calibration mode, press
[ CHANNEL / + ] or
[ MEM / - ] key to modify 1% of the value. Long press to quick-
adjust the value.
Humidity calibration mode
9. If the current reading of the selected channel displays the flashing
“
--”, “Hi” or “Lo”, it will be impossible to adjust. Pressing
[ CHANNEL / + ] or [ MEM / - ] key will not change the value.
10. If re-enter temperature and humidity calibration mode, the
adjusted value will reset to the original value.
11. The comfort indication is based on calibrated temperature and
humidity values to calculate.
MAX/MIN TEMPERATURE AND HUMIDITY RECORD
The unit preserves the MAX/MIN temperature and humidity records
The unit preserves the MAX/MIN temperature and humidity records
since the last manual reset.
1. In normal mode, press
1. In normal mode, press
[ MEM / - ] key once to show the current
maximum temperature and humidity values; press again to show
the minimum values; press the third time to return to normal
mode.
2. When the MAX/MIN records are shown, the display will return to
normal mode after leaving the unit for 5 seconds.