Справочник Пользователя для ICOM 376500
vii
PRECAUTIONS
R DANGER HIGH RF VOLTAGE! NEVER touch an
antenna or antenna connector while transmitting. This could
cause an electrical shock or burn.
antenna or antenna connector while transmitting. This could
cause an electrical shock or burn.
R DANGER! NEVER operate the transceiver near
unshielded electrical blasting caps or in an explosive
atmosphere. This could cause an explosion and death.
unshielded electrical blasting caps or in an explosive
atmosphere. This could cause an explosion and death.
R WARNING RF EXPOSURE! This device emits Radio
Frequency (RF) energy. Extreme caution should be
observed when operating this device. If you have any
observed when operating this device. If you have any
questions regarding RF exposure and safety standards
please refer to the Federal Communications Commission
please refer to the Federal Communications Commission
Ofice of Engineering and Technology’s report on
Evaluating Compliance with FCC Guidelines for Human
Evaluating Compliance with FCC Guidelines for Human
Radio Frequency Electromagnetic Fields (OET Bulletin 65).
R WARNING! NEVER operate the transceiver with a
headset or other audio accessories at high volume levels. If
you experience a ringing in your ears,reduce the volume or
discontinue use.
headset or other audio accessories at high volume levels. If
you experience a ringing in your ears,reduce the volume or
discontinue use.
R WARNING! NEVER
apply AC power to the [DC13.8V]
socket on the transceiver rear panel. This could cause a ire
or damage the transceiver.
or damage the transceiver.
R WARNING! NEVER
apply more than 16 V DC to the
[DC13.8V] socket on the transceiver rear panel. This could
cause a ire or damage the transceiver.
R WARNING! NEVER
reverse the DC power cable
polarity. This could cause a ire or damage the transceiver.
R WARNING! NEVER
remove the fuse holder on the DC
power cable. Excessive current caused by a short could
cause a ire or damage the transceiver.
R WARNING! NEVER let metal, wire or other objects
contact the inside of the transceiver, or make incorrect
contact with connectors on the rear panel. This could cause
an electric shock or damage the transceiver.
contact the inside of the transceiver, or make incorrect
contact with connectors on the rear panel. This could cause
an electric shock or damage the transceiver.
R WARNING! NEVER operate or touch the transceiver
with wet hands. This could cause an electric shock or
damage to the transceiver.
with wet hands. This could cause an electric shock or
damage to the transceiver.
R WARNING!
Immediately turn OFF the transceiver power
and remove the DC power cable from the transceiver if it
emits an abnormal odor, sound or smoke. Contact your
Icom dealer or distributor for advice.
emits an abnormal odor, sound or smoke. Contact your
Icom dealer or distributor for advice.
R WARNING! NEVER put the transceiver on an unstable
place where the transceiver may suddenly move or fall.
This could cause an injury or damage the transceiver.
place where the transceiver may suddenly move or fall.
This could cause an injury or damage the transceiver.
R WARNING! NEVER operate the transceiver during a
lightning storm. It may result in an electric shock, cause
lightning storm. It may result in an electric shock, cause
a ire or damage the transceiver. Always disconnect the
power souce and antenna before a storm.
power souce and antenna before a storm.
CAUTION: NEVER expose the transceiver to rain, snow or
any liquids.
CAUTION: NEVER change the internal settings of the
transceiver. This could reduce transceiver performance
and/or damage to the transceiver. The transceiver warranty
does not cover any problems caused by unauthorized
internal adjustments.
transceiver. This could reduce transceiver performance
and/or damage to the transceiver. The transceiver warranty
does not cover any problems caused by unauthorized
internal adjustments.
CAUTION: NEVER install or place the transceiver in a
place without adequate ventilation, or block any cooling
vents on the top, rear, sides or bottom of the transceiver.
Heat dissipation may be reduced and damage the
transceiver.
vents on the top, rear, sides or bottom of the transceiver.
Heat dissipation may be reduced and damage the
transceiver.
CAUTION: NEVER
use harsh solvents such as Benzine or
alcohol when cleaning, as they will damage the transceiver
surfaces.
surfaces.
CAUTION: NEVER leave the transceiver in areas with
temperatures below –10°C (+14°F) or above +60°C
(+140°F) for mobile operations.
CAUTION: NEVER place the transceiver in excessively
dusty environments. This could damage the transceiver.
dusty environments. This could damage the transceiver.
DO NOT place the transceiver against walls or putting
anything on top of the transceiver. This may overheat the
transceiver.
anything on top of the transceiver. This may overheat the
transceiver.
BE CAREFUL! The Main unit will become hot when
operating the transceiver continuously for long periods of
time.
operating the transceiver continuously for long periods of
time.
CAUTION:
If you use a linear ampliier, set the
transceiver’s RF output power to less than the linear
ampliier’s maximum input level, otherwise a high input
could damage the linear ampliier.
CAUTION: Use only Icom supplied or optional
microphones. Other manufacturer’s microphones may have
different pin assignments, and could damage the connector
and/or the transceiver.
different pin assignments, and could damage the connector
and/or the transceiver.
NEVER leave the transceiver in an insecure place to avoid
use by unauthorized persons.
use by unauthorized persons.
Turn OFF the transceiver’s power and/or disconnect the AC
power cable when you will not use the transceiver for a long
period of time.
power cable when you will not use the transceiver for a long
period of time.
Turn OFF the transceiver’s power and/or disconnect the DC
power cable when you will not use the transceiver for long
period of time.
power cable when you will not use the transceiver for long
period of time.
The LCD display may have cosmetic imperfections
that appear as small dark or light spots. This is not a
that appear as small dark or light spots. This is not a
malfunction or defect, but a normal characteristic of LCD
displays.
displays.