Справочник Пользователя для SHEN ZHEN XING YAO HUA INDUSTRIAL CO. LTD T6AH-2400

◇To Access the Aileron-to-Rudder Mix Function
Press the DOWN and SELECT keys simultaneously to access the Function Mode.

In Function Mode, use the UP or DOWN key to select the AILE-RUDD MIX screen.

Press the SELECT key to select RATE or SW (switch).

◇

To Adjust the Mix Value

With RATE highlighted, press the INCREASE or DECREASE keys to adjust the

mix value. Note: reversing mix directions is accessible.
◇To Assign a Switch
With SW be choosed, press the INCREASE or DECREASE keys to select the

desired switch used to turn on/off the mix (Flap 0 or Mix).
◆Flap System

The purpose of the Flap System is to set the flap and elevator positions for landing

and takeoff. This is accomplished by selecting values for the elevator and flaps to

be activated when the Land Switch is engaged. Three flap and elevator positions

are available. The landing system can also be activated by a preset position of the

throttle stick. Refer to the Automatic Landing Attitude section for more information

on how to select the preset throttle position.

Note: The Flap System is only be accessed when SYSTEM is selected under Flap

in the Input Select screen. See page 46 for more detail

◇Accessing and Utilizing the Flap System
Press the UP and SELECT keys simultaneously to enter the Function Mode.

Press the UP or DOWN keys until FLAP SYS appears in the upper left portion of the

LCD. Press the SELECT key to move the cursor at the desired function (i.e., ELEV,

FLAP , SPOI, AUTO). Note: The flap system can only be accessed when SYSTEM

is selected in the Input Select screen under flaps. See page 41 for more details.

Press the UP or DOWN keys to set the flap and elevator travel. The UP key adds up

flap/elevator and the DOWN key adds down flap/elevator. The input is adjustable

from 125% for flap and -200% for elevator.

◆

Automatic Landing

When the Automatic Landing Function is active, the throttle stick will activate the

landing system you have just set up. Any point of throttle stick travel can be set as

the “auto-land” point. Once the throttle stick passes through this point and the

LAND switch is in the MID, or land position, the landing system will be activated.

Thus, the elevator and flaps would be activated. If the flap mixing switch is not in

the LAND position, the throttle stick operation would have no effect on the landing

system.

◇To Activate the Automatic Landing Feature
In the FLAP SYS. screen, press the SELECT key until AUTO is selected.

Press the INCREASE or DECREASE key to activate the AUTOMATIC LANDING

SYSTEM. Press the INCREASE or DECREASE key to adjust the value (0% = low

stick while 100% = full stick). To clear the auto land point, press CLEAR key and

the display will return to INH.

◆Differential Aileron Mixing
Note: Only available when Flaperon or Elevon is selected, the Differential System

is available (see Tail Wing Type Page 44).

The Differential Aileron function allows precise electronic adjustments of the up vs

. down aileron travel of both ailerons. Aileron differential is used to reduce unwanted

yaw characteristics during roll inputs. In order to access the Differential Function,

flaperon or elevon wing mixing must be selected and two servos must be used to

operate the ailerons.

[FLAP SYS.] NORM

FLAP ELEV

NORM UP100% 0

0
0

MID
LAND

AUTO INH

DN100%

Press to enter FLAP SYSTEM

Press to enter
Function Mode

Press to return
value to default

Press to highlight
the desired function

Press to adjust value

[ DIFFERENTIAL ]

Press to enter DIFFERENIAL

Press to enterFunction Mode Press to return value to default

Press to adjust value

FLAPERON

NORM

[FLAP SYS.] NORM

FLAP ELEV

NORM Up100%

0
0

MID
LAND

AUTO INH

DN100%

Press to enter FLAP SYSTEM

Press to enterFunction Mode Press to return value to default

Press to adjust value