Справочник Пользователя для ALPWISE BLEM003
ALPW-BLEM003
Bluetooth® Smart Embedded Module
Datasheet
ALPWISE S.A.S. – LE PULSAR, 4 Avenue Doyen Louis Weil, 38000 GRENOBLE, France
Tel: +33 4 76 22 02 24– Email: alpwisesales@alpwise.com –
Tel: +33 4 76 22 02 24– Email: alpwisesales@alpwise.com –
Revision 1.2
8
9 Certifications
9.1
Bluetooth SIG
Certification pending.
9.2
FCC and IC
The ALPW-BLEM003 is certified compliant with
the FCC CFR 47 Part 15, Subpart B and C, and RSS-
210 Issue 8.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
the FCC CFR 47 Part 15, Subpart B and C, and RSS-
210 Issue 8.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful
interference, and
(2) this device must accept any
interference
interference
received,
including
interference that may cause undesired
operation.
operation.
Any changes or modifications not expressly
approved by ALPWISE could void the user’s
authority to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. End users must follow the specific
operating instructions for satisfying RF exposure
compliance. This transmitter meets both portable
and mobile limits as demonstrated in the RF
Exposure Analysis. This transmitter must not be
co-located or operating in conjunction with any
other antenna or transmitter except in
accordance with FCC multi-transmitter product
procedures.
IC Statements:
This device complies with Industry Canada licence-
exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may
not cause interference, and (2) this device must
accept any interference, including interference
that may cause undesired operation of the device.
Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for
the transmitter by Industry Canada. To reduce
potential radio interference to other users, the
antenna type and its gain should be so chosen
that the equivalent isotropically radiated power
approved by ALPWISE could void the user’s
authority to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. End users must follow the specific
operating instructions for satisfying RF exposure
compliance. This transmitter meets both portable
and mobile limits as demonstrated in the RF
Exposure Analysis. This transmitter must not be
co-located or operating in conjunction with any
other antenna or transmitter except in
accordance with FCC multi-transmitter product
procedures.
IC Statements:
This device complies with Industry Canada licence-
exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may
not cause interference, and (2) this device must
accept any interference, including interference
that may cause undesired operation of the device.
Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for
the transmitter by Industry Canada. To reduce
potential radio interference to other users, the
antenna type and its gain should be so chosen
that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for
successful communication.
OEM Responsibilities to comply with FCC and
Industry Canada Regulations
The ALPW-BLEM003 module has been certified for
integration into products by OEM integrators
under the following condition:
successful communication.
OEM Responsibilities to comply with FCC and
Industry Canada Regulations
The ALPW-BLEM003 module has been certified for
integration into products by OEM integrators
under the following condition:
The transmitter module must not be co-
located or operating in conjunction with
any other antenna or transmitter except
in accordance with FCC multi-transmitter
product procedures.
located or operating in conjunction with
any other antenna or transmitter except
in accordance with FCC multi-transmitter
product procedures.
As long as the two condition above is met, further
transmitter testing will not be required. However,
the OEM integrator is still responsible for testing
their end-product for any additional compliance
requirements required with this module installed
(for example, digital device emissions, PC
peripheral requirements, etc.).
IMPORTANT NOTE : In the event that these
conditions can not be met (for certain
configurations or co-location with another
transmitter), then the FCC and Industry Canada
authorizations are no longer considered valid and
the FCC ID and IC Certification Number can not be
used on the final product. In these circumstances,
the OEM integrator will be responsible for re-
evaluating the end product (including the
transmitter) and obtaining a separate FCC and
Industry Canada authorization.
End Product Labeling
The BLEM003 module is labeled with its own FCC
ID and IC Certification Number. If the FCC ID and
IC Certification Number are not visible when the
module is installed inside another device, then the
outside of the device into which the module is
installed must also display a label referring to the
enclosed module. In that case, the final end
product must be labeled in a visible area with the
following:
“Contains FCC ID: 2ABXUBLEM003”
“Contains IC: 11797A-BLEM003”
The OEM integrator has to be aware not to
provide information to the end user regarding
transmitter testing will not be required. However,
the OEM integrator is still responsible for testing
their end-product for any additional compliance
requirements required with this module installed
(for example, digital device emissions, PC
peripheral requirements, etc.).
IMPORTANT NOTE : In the event that these
conditions can not be met (for certain
configurations or co-location with another
transmitter), then the FCC and Industry Canada
authorizations are no longer considered valid and
the FCC ID and IC Certification Number can not be
used on the final product. In these circumstances,
the OEM integrator will be responsible for re-
evaluating the end product (including the
transmitter) and obtaining a separate FCC and
Industry Canada authorization.
End Product Labeling
The BLEM003 module is labeled with its own FCC
ID and IC Certification Number. If the FCC ID and
IC Certification Number are not visible when the
module is installed inside another device, then the
outside of the device into which the module is
installed must also display a label referring to the
enclosed module. In that case, the final end
product must be labeled in a visible area with the
following:
“Contains FCC ID: 2ABXUBLEM003”
“Contains IC: 11797A-BLEM003”
The OEM integrator has to be aware not to
provide information to the end user regarding