Справочник Пользователя для Fortin Auto Radio Inc. A2W01FM
Press two times (2x) on the FUNCTION button
LED
SPEAKER
VEHICLE STATUS (IF EQUIPPED)
1 Green flash
1beep
The vehicle is LOCKed (and ARMed)
2 Green flashes
2 beeps
The vehicle is UNLOCKed (and DISARMed)
1 Green flash
Ascending tone
The vehicle is running by remote-start.
COLD START TIMER MODE
Cold Start Timer Mode will remote-start the vehicle when the tempeture is below -5
0
C / 23
0
F every 1.5 or 3 hours
and run for 3, 5, 7 or 15 minutes (6, 14 or 30 for diesel engines), depending on programming. The remote-starter
will repeat this sequence for up to a maximum of 24 hours. For manual transmission vehicle’s READY MODE must
be enabled, and if at any time READY MODE is disabled this sequence will cancel.
will repeat this sequence for up to a maximum of 24 hours. For manual transmission vehicle’s READY MODE must
be enabled, and if at any time READY MODE is disabled this sequence will cancel.
WARNING Do not start the vehicle indoors (garage, underground parking).
To enable Cold Start Timer Mode proceed with the following steps.
Press simultaneously LOCK and START buttons for 1 second until the park-
ing light flash once. The remote Green Led flash and bip once to confirm.
ing light flash once. The remote Green Led flash and bip once to confirm.
To disable Cold Start Timer Mode do any of the following:
•
Press simultaneously LOCK and
START buttons for 1 second until
the parking light flash twice.
START buttons for 1 second until
the parking light flash twice.
•
Put the Remote-Starter/alarm into Valet
Mode. Remote-Start the vehicle.
Mode. Remote-Start the vehicle.
•
Open the hood.
•
Press the brake pedal.
•
Turn the key to the ignition
(ON / RUN) position.
(ON / RUN) position.
•
Disable Ready Mode
(manual transmission).
(manual transmission).
Note: If the Alarm is triggered during Remote-Start (Cold Start), the vehicle will stop running,
but Cold Start will not cancel it’s schedule.
but Cold Start will not cancel it’s schedule.
AUXILIARY USE
Aux 1 : Drivers side sliding door (if installed) :
Press and relase the FUNCTION (the remote LED flashes slowly white) but-
ton than you have 12 seconds to press the button LOCK button.The remote
Green Led flash and bip once to confirm.
ton than you have 12 seconds to press the button LOCK button.The remote
Green Led flash and bip once to confirm.
Aux 2 : Passenger side sliding door (if installed).
Press and relase the FUNCTION button (the remote LED flashes slowly white)
than you have 12 seconds to press the UNLOCK button.The remote Green
Led flash and bip once to confirm.
than you have 12 seconds to press the UNLOCK button.The remote Green
Led flash and bip once to confirm.
Note:
The function of the auxiliary outputs may vary depending on the vehicle and the installation. In most cases
these outputs are not used, and in some cases they may be used to control other features such as the power win-
dows, sunroof, or heated seats. Check with the installer to find out what AUX outputs have been installed, and what
they control.
dows, sunroof, or heated seats. Check with the installer to find out what AUX outputs have been installed, and what
they control.
REMOTE STARTING OPTIONS
CONFIGURABLE FONCTIONALITY DURING INSTALLATION
This Remote-Starter is designed to be highly flexible when integrating into original equipment (OEM). With the fol-
lowing programmable options the Remote-Starter/Alarm can control most electronic systems within the vehicle.
lowing programmable options the Remote-Starter/Alarm can control most electronic systems within the vehicle.
WARNING:
This Remote-Starter must be installed by a trained professional. Improper modifications to any of the
following settings could adversely affect the reliability of the Remote-Starter and/or the vehicle’s operation.
Configurable Options:
- Remote Door Locks
- Active or Passive Arming
- Ignition Door Locks
- Security Lock
- Trunk/Hatch Release
- Runtime
Page 10 / 13